Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 200

Страница: 200 / 456

5.6

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Front Fender Removal / Installation

Remove the front rack / storage box lid and the front
bumper as outlined in this chapter.

Remove the plastic inserts (A) that secure the front
fender to the upper strut support.

Remove the screws that secure the front fender to
the frame in the fuel tank mount area.

Remove the screws (C) that attach the front cab to
the frame in the front rack area.

Remove the seat and side panels, refer to the “SIDE
PANEL REMOVAL” section.

Remove the plastic inserts (D) that secure the front
of the foot wells to the front fender.

Remove the fuel cap and place a clean lint free shop
towel into the tank neck to keep any debris from
falling into the tank.

The front fender should now slide back over the fuel
tank and fuel tank neck.

Reverse the removal steps for installation. Torque (6)
front fender-to-frame screws to specification.

Fender to Frame Screws

24 in-lbs (2.7 Nm)

BODY / STEERING / SUSPENSION

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды