Polaris 2014 Sportsman 570 EF Скачать руководство пользователя страница 132

Страница: 132 / 456

3.74

9924871 R03 - 2014 Polaris Sportsman® 570 EFI Service Manual

Remove the center gerotor, pin and shaft from the oil
pump cover.

NOTE: There is a spacer in between the inner oil
pump gerotor and the oil pump cover.

Remove the oil pump gerotor that is in the engine
case (if needed).

10. Clean the gerotors to remove oil.

11. Inspect surfaces of pump cavity in crankcase and

surface of pump cover for scoring or wear.

12. Inspect gerotor for scoring or other damage. Replace

parts as a set if damaged.

Oil Pump Assembly

Clean and dry all parts thoroughly. Apply clean
engine oil to all parts. Do not use gasket sealer on
the pump cover mating surfaces.

Align the gerotor according to the orientation dots.

Place the drive pin (A) through the oil pump drive
shaft.

Slide the gerotor (B) onto the drive shaft and lock
them into position on the drive pin.

Install the washer (C) onto the drive shaft.

Install the oil pump cover (D) onto the shaft
assembly.

Grasp the complete oil pump assembly by the drive
shaft(1) and install the assembly into the crankcase.

Install the oil pump cover bolts (2) and torque to
specification.

Oil Pump Cover Bolt:

7.5 ft-lbs (10 Nm)

Install the upper oil pump sprocket spacer.

10. Install the oil pump sprockets, chain, washer and

new

bolts. Oil pump sprockets must be installed in

the correct position, with the word “

OUT

” facing out.

ENGINE

Содержание 2014 Sportsman 570 EF



























































































































































































































































































































































































































Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды

Polaris 2014 Sportsman 570 EF, Руководство по обслуживанию

Результаты поиска

Содержание 2014 Sportsman 570 EF

Отзывы:

Похожие инструкции для 2014 Sportsman 570 EF

Бренды по названию

Популярные бренды