Polaris 2005 Sportsman MV7 Скачать руководство пользователя страница 41

Страница: 41 / 312

MAINTENANCE

2.23

3. Remove the pressure cap (1).
4. Using a funnel, slowly add coolant through the

radiator filler neck.

5. Reinstall the pressure cap.
6. Reinstall the front rack.

NOTE:

Use of a non-standard pressure cap will not

allow the recovery system to function properly.

Contact your dealer for the correct replacement part.

Radiator

Cap

AIR FILTER/PRE-FILTER
SERVICE

It is recommended that the air filter and pre filter be

replaced annually. When riding in extremely dusty

conditions, replacement is required more often.
The pre filter should be cleaned before each ride using

the following procedure:
1. Lift up on the rear of the seat.
2. Pull the seat back and free of the tabs.

NOTE:

When reinstalling seat, make sure the slots in the

seat engage the tabs in the fuel tank.

3. Remove clips (A) from air box cover and remove

cover. Inspect the gasket. It should adhere tightly

to the cover and seal all the way around.

4. Loosen

clamp

and

remove

air

filter

assembly.

Gasket

Cover

Pre-filter

Main Element

Ill.1

Cleaning:

5. Slip the pre-filter element off of main element.

Clean the pre filter with high flash point solvent,

followed by hot soapy water.

6. Rinse and dry thoroughly.
7. Inspect element for tears or damage.
8. Apply foam filter oil or clean engine oil and

squeeze until excess oil is removed.

9. Inspect main filter and replace if necessary. If the

filter has been soaked with fuel or oil it must be

replaced.

Installation:

10. Reinstall pre-filter element over main filter. Be

sure the element covers entire surface of main

filter without folds, creases, or gaps.

Содержание 2005 Sportsman MV7

























































































































































































































































































































Результаты поиска

Содержание 2005 Sportsman MV7

Отзывы:

Бренды по названию

Популярные бренды

Polaris 2005 Sportsman MV7, Руководство по обслуживанию

Результаты поиска

Содержание 2005 Sportsman MV7

Отзывы:

Бренды по названию

Популярные бренды