ADVANCED MENU
Infi nite Intervalometer
*
/MENU A B
Activates camera shutter release at set interval for set number of
activations. Use for time-lapse photography applications or other effe
ff cts.
Set interval (amount of time betw
ee een activations) in Hours:Minutes:Seconds,
then set count - set to 0 for infi nite count. Connect remote camera cable
to
/P2 or ACC. Press
TEST
to start cycle, hold
*
/MENU
to cancel.
Intervalometer is not transmitted in
tt
TRANSMIT mode – only directly
attached cameras are activated.
Multi-Pop
*
/MENU A C
Activates connected fl ash at set interval for set number of activations.
Use for increasing depth of fi eld with multiple fl ashes at safe intervals
for recycling, or other time-lapse effects. Set interval (amount of time
between activations) in Seconds, then set count - set to 0 for infi nite
count. Connect fl ash sync cable to
/P2. Press
TEST
to start cycle,
hold
*
/MENU
to cancel. Multi-Pop is not transmitted in TRANSMIT
mode – only directly atta
tt ched fl ash units are activated. For remote fl ash
Multi-Pop, set Multi-Pop on each individual fl ash unit’s MultiMAX II (set
for RECEIVE).
FCC WANTS YOU TO KNOW
WARNING: Changes or modifi cations to this unit not expressly
approved by the party responsible for compliance could
void the user’s authority to operate this equipment.
NOTE
: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harm-
ful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy, and, if not installed and
used in accordance with the instructions, may cause harmful interf
ee erence
to radio communications. Mounting and cable connections detailed
in this document represent the intended usage, however, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to
rr
correct the interference by one or
more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and the receiver.
3. Consult the dealer or an experienced radio or television technician
for help.
This device complies with Part 15 of the FCC rules and also with RSS-210
of Industry Canada. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
MultiMAX FCC ID: KDS-PW2-201
MultiMAX IC ID: 2170A0PW201
Simplifi ed EU Declaration of Conformity
Hereby, LPA Design Inc. South Burlington VT USA declares that the radio
equipment type PocketWizard MultiMAX II CE wireless photographic
remote control is in compliance with Directive 2014/53/EU. The full text
of the EU declaration of conformity is available at the following internet
address:
www.pocketwizard.com/support/reference/CE/
13175 v1.0
Information subject to change. Visit
wiki.PocketWizard.com
for more
details and the latest information.
Help
:
wiki.PocketWizard.com
PocketWizard.com/support
[email protected]
Warranty / Registration
This PocketWizard
®
product is covered by a two-year limited
manufacturer’s warranty. For details, or to register your
r
radio, use
the links below or contact your distributor via
PocketWizard.com
.
PocketWizard / LPA Design
At
tn: Warranty
21 Gregory Drive
Suite 140
South Burlington, VT 05403, USA
Registration
:
PocketWizard.com/warranty
Patent Information
:
www.pwpatents.com
IMPORTAN
T
T
T
: FCC/IC frequency radios are NOT compatible
with CE frequency radios and vice versa.
PocketWizard.com/wheretobuy/frequency
.
© 2017 LPA Design. All rights reserved. Product features and specifications are
subject to change without notice. PocketWizard, ControlTL, MiniTT1, FlexTT
x
5,
HyperSync, Plus and MultiMAX are either trademarks or registered trademarks
of LPA Design. All other trademarks contained herein are the property of their
respective owners.
ADVANCED MENU
TRANSMIT DELAY MENU
A
A
TRANSMIT Delay - R /P2
*
/MENU A A A
(see Fig. 1)
Delays sync to all remote units and l
tt
ocal /P2. On main screen, small D
below
TX
indicates local /P2 will be delayed. Use for controlling sync
timing in long exposures, rear curtain sync fi ne-tuning, and other effects.
TRANSMIT Delay - Remotes Only
*
/MENU A A B
(see Fig. 1)
Delays sync to remote units on
tt
ly. Local /P2 syncs immediately. Use
for delaying remote fl ash to not affect l
t ocal fl ash metering or other effects.
TRANSMIT Delay - Rear Curtain Sync
*
/MENU A A C
(see Fig. 2)
Provides rear curtain sync effect to cameras without this feature, or
to cameras with feature but not compatible with rear c radio
(problem = no fl ash sync or shutter clipping appears when using radio).
Use
▲▼
to match MultiMAX II shutter speed setting with camera
shutter speed. Use
*
/MENU A A A
for fi ne adjustments or for
shutter speeds other than provided.
TRANSMIT - SpeedCycler
*
/MENU A D
Helps reduce fl ash recycle time by cycling through multiple
remote fl ashes.
On Standard Channels 17 - 32, selected Zones are used.
On Standard Channels 1 - 16, follow prompts to select start
and end channel for up to 16 fl ashes.
Arrow indicates next channel/zone to sync.
ADVANCED MENU
RECEIVE DELAY MENU
A
A
RECEIVE Delay -
/P1 + /P2
*
/MENU A A A
(see Fig. 1)
Delays sync to
/P1,
/P2 and ACC ports. On main screen, small D
below –RX– indi
–
cates /P2 will be delayed. Use for controlling fl ash
sync timing in long exposures and other effects. Set different delays
on multiple receiving MultiMAX II radios for customized and repeatable
fl ash sequences.
RECEIVE Delay - /P2 Only
*
/MENU A A B
(see Fig. 1)
Delays sync to /P2 only.
/P1 and ACC sync immediately.
Use for double exposure or other special effects.
RECEIVE Delay - Equalize
*
/MENU A A C
Helps synchronize multiple cameras (1/125 shutter speed) to single
fl ash and enables lag time measurement of camera. Connect camera
PC sync cable to
/P1 or slide MultiMAX II (set for RECEIVE) onto
camera shoe. Connect remote camera cable to
/P2 or ACC. Press
TEST
several times to measure camera lag. When number displayed
seems consistent, press
*
/MENU
to accept. Perform same operation
on other cameras. Connect separate MultiMAX II (set for RECEIVE)
to fl ash and on that unit press
*
/MENU A A C
*
/MENU
(accept displayed 0.1500 setting). Initiate sequence with separate
transmitting PocketWizard radio.
RECEIVE - Fast Mode
*
/MENU A D
Enables faster fl ash sync shutter speeds with compatible fl ash
units and cameras, up to 1/1000 second. Main screen displays
FAST MODE. Quad-Zone Triggering and Confirmation are not
available in Fast Mode.
MORE MODES
Long Range
*
/MENU L A A
Doubles usable distance for Standard Channels 17 – 32 only.
LT
or
–LR- will be displayed. All radios must be set to LT/L
T
T R to work to
k
gether.
Best for remote camera. Fastest fl ash sync shutter speed in LT/L
T
T R is
1/125. Radio confirmation not available.
Normal Range
*
/MENU L A B
Returns radios to normal range operation with all features available.
Close Range
*
/MENU L A C
Reduces transmit power for working within a few feet of receiving radios.
CT
CT
will be displayed. Affects all Standard Channels 1-32 and
ControlTL Channels 1-20. Receivers must be in Normal Range Mode.
Disconnect Hot Shoe
*
/MENU L B
Disables and enables hot shoe input. Use when mounted on a camera
to prevent inadvertent sync.
Hibernate/Auto Sleep
*
/MENU L C A
Set a timer for entering batt
aa ery saving mode. Awaken by pressing
TEST
for 3
r
seconds in RECEIVE mode, send a signal from a TRANSMIT radio
for 3 seconds. Use when deploying radio a few days prior to event.
Hibernate/Auto Shutdown
*
/MENU L C B
When enabled, radio will power off af
ff
ter 40 hours to preserve batteries
and prevent potential battery leak damage. Default = Disabled
Noise Sniffer
*
/MENU L D
Find sources of radio interference. Lower numbers are better.
Press
*
/MENU
to exit.
Signal Strength Indicator
Automatic. RECEIVE only. Note signal bars in top line of LCD after each
sync. More bars = better signal. Re-orient radio(s) to improve signal.
