Plymovent MobilegoPlus Скачать руководство пользователя страница 4

0000111659/140921/C MobileGo 

3

Available connection 

voltages

 

- 115V/1ph/50Hz

 

- 115V/1ph/60Hz

 

- 230V/1ph/50Hz

Motor design

IEC

Energy efficiency

n.a.

Mains cord

5 m

Plug:

 

- 115V/1ph/50Hz

 

- 115V/1ph/60Hz

 

- 230V/1ph/50Hz

Type:

 

- none

 

- none

 

- F

Welding fume class

W3 compliant

according to EN-ISO 21904-2-2020

1.3.1  Dimensions

Refer to Fig. I on page 10.

1.4 

Working range

Refer to Fig. II on page 10.

1.5 

Ambient and process conditions

Process temperature:

 

- min.

 

- nom.

 

- max.

5°C (41°F)

20°C (68°F)

70°C (158°F)

Max. relative humidity

90%

Suitable for outdoor use

no

Refer to the available product data sheets for 

detailed product specifications.

1.6 

Transport of the unit

You cannot hold the manufacturer liable for any transportation 

damage after delivery of the product.

 

-

Handle the filter unit and the accompanying extraction arm 

with care.

 

- Completely dismount the extraction arm before transport. 

Dismount the arm by executing the mounting procedure in 

reverse order. Subsequently the filter unit and the arm can 

be transported on a pallet in the original packing.

 

-

To prevent damage, make sure that the filter unit and the 

arm cannot shift on the pallet.

PRODUCT DESCRIPTION

2.1 

Components

The product consists of the following main components and 

elements:

Fig. 2.1

Shut-off damper

B  Extraction arm (shown: hose tube arm)

C  Control panel

Pre filter cassette

HEPA filter cassette

F  Fan + motor

Fig. 2.1 

B

A

C

D

E

F

Main components and elements

2.2 

Operation

The MobileGo works in accordance with the 

recirculation principle. Welding fume is extracted 

through the hood of the connected extraction arm 

by the built-in fan. The polluted air passes the pre filter 

cassette and is cleaned by the HEPA filter cassette.

The cleaned air is returned in the workshop through the outlet 

grid on the rear of the unit.

2.2.1 

Indication of filter replacement

The MobileGo has a service indicator that monitors the airflow. 

It gives an acoustic signal to replace the filter(s).

SAFETY INSTRUCTIONS

General

The manufacturer does not accept any liability for 

damage to the product or personal injury caused by 

ignoring of the safety instructions in this manual, or 

by negligence during installation, use, maintenance, and repair 

of the product mentioned on the cover of this document and 

any corresponding accessories.

Specific working conditions or used accessories may require 

additional safety instructions. Immediately contact your 

supplier if you detect a potential danger when using the 

product.

The user of the product is always fully responsible for 

observing the local safety instructions and regulations. 

Observe all applicable safety instructions and 

regulations.

User manual

 

- Everyone working on or with the product, must be familiar 

with the contents of this manual and must strictly observe 

the instructions therein. The management should instruct the 

personnel in accordance with the manual and observe all 

instructions and directions given.

 

- Do not change the order of the steps to perform.

 

- Keep the manual with the product.

Содержание MobilegoPlus





















Отзывы: