0000103355/240315/A FUA-1800/2100/2700/3000/4700 (60Hz)
EN - 5
requirements, codes and/or laws. Ensure compliance with
the EMC regulatory arrangements.
- During installation, always use Personal Protective
Equipment (PPE) to avoid injury. This also applies to persons
who enter the work area during installation.
- Do not install the product in front of entrances and exits
which must be used for emergency services.
- Mind any gas and water pipes and electric cables.
- Make sure that the workshop, in the vicinity of the product,
contains sufficient approved fire extinguishers.
Use
WArNiNg
Fire hazard! Do
not
use the product for:
-
extracting flammable, glowing or burning particles
or solids or liquids
- extracting of aggressive fumes (such as
hydrochloric acid) or sharp particles
- sucking cigarettes, cigars, oiled tissues, and other
burning particles, objects, and acids
WArNiNg!
Do
not
use the product for:
- aluminium laser cutting
- paint mist
- extraction of hot gases (more than 176°F/80°C
continuously)
- grinding aluminium and magnesium
-
flame spraying
- extraction of cement, saw dust, wood dust etc.
- sucking cigarettes, cigars, oiled tissues and other
burning particles, objects and acids
- explosive environments or explosive substances/
gases
Note: this list is not all-encompassing.
- Check the working environment. Do not allow unauthorized
persons to enter the working environment.
-
Make sure the room is always sufficiently ventilated; this
applies especially to confined spaces.
service, maintenance and repairs
- During service, maintenance and repair jobs, always use
Personal Protective Equipment (PPE) to avoid injury. This
also applies to persons who enter the work area during
installation.
- Always use tools, materials, lubricants and service
techniques which have been approved by the manufacturer.
Do not use worn tools and do not leave any tools in or on the
product.
- Safety features which have been removed for service,
maintenance or repairs, must be put back immediately after
finishing these jobs and it must be checked that they still
function properly.
4
iNstAllAtiON
4.1
Unpacking
Check that the product is complete. The package should
contain:
- extraction fan incl. inlet grid 3 mm (0.12 in.)
-
connection flange with grid
4.1.1 Options and accessories
The MB-FUA/S1-2 kit should contain:
- mounting bracket
- tube clamps (4)
- hardware
The MB-FUA/C1-2 kit should contain:
- mounting bracket
- hardware
The OL (outlet transition)
2
should contain:
- square to round outlet transition
The SC (soft connection) should contain:
- soft connection with 2 hose clamps
If parts are missing or damaged, contact your supplier.
4.2
installation
4.2.1 Tools and requirements
The following tools are necessary for installing the fan:
- wrench 10 mm
- wrench 13 mm
- wrench 17 mm
- screwdriver
4.2.2 Installing the fan on an MB-FUA-S1/S2
For use as a stand alone or for mounting on the wall, ceiling or
a platform. The motor can be installed resting on the stand.
The motor of the FUA-1800/2100/2700 can also be installed
upside down (hanging from the stand, not shown).
To install the fan on an MB-FUA-S1/S2 stand, proceed as
follows:
•
Install the stand in the desired place.
•
Attach the tube clamps (B) as desired, if applicable.
•
Tighten the tube clamps with suitable hardware (not
supplied; material depending on wall, floor or ceiling type).
•
Position the fan on the stand as desired.
•
Tighten the bolts (A).
Fig. 4.1
A (x 4)
B (x 4)
Installing the fan on an MB-FUA-S1/S2
4.2.3 Installing the fan on an MB-FUA-C1/C2
For use on an extractor (UK, FlexMax or FEB) or use with
vehicle exhaust extraction systems.
To install the fan on an MB-FUA-C1/C2 bracket, proceed as
follows:
•
Use the mounting holes (A) and suitable hardware (not
supplied, material depending on wall type) to install the
bracket on the wall.
•
Position the fan on the bracket.
•
Tighten the bolts (B).
2. Only applicable for FUA-3000/4700.
FUA-1800/2100/2700 come pre-installed with outlet transition.
