Plymovent CONTROLPRO, Руководство по установке

Страница: 15 / 23

0000112606/010720/A ControlPro 14
3/2 solenoid valve
Valve to shut off the compressed air supply in case of fire in
the extraction/filter system. For enhanced safety it releases
the air from the filter’s compressed air tank a the same time.
Connection/functionality:
- output signal to shut off the compressed air supply and to
release the compressed air tank
Indicator LED’s Valves
Dustbin
sensor
Fan Pressure
sensor
Digital input 1-5 RS485 VFD CAN Slave
CAN HMI Digital input 6-12
Filter Pressure
sensor
Analog
output
Light tower
Power
Rela
ys
Cable #18
Digital input 1-5
1
+ 24V
2
IN 1
3
+ 24V
4
IN 2
5
+ 24V
6
IN 3
7
+ 24V
8
IN 4
9
+ 24V
10
IN 5
11
COM1
12
GND
Digital input 1-5
1
+ 24V
2
IN 1
3
+ 24V
4
IN 2
5
+ 24V
6
IN 3
7
+ 24V
8
IN 4
9
+ 24V
10
IN 5
11
COM1
12
GND
Digital input 6-12
1
+ 24V
2
IN 6
3
+ 24V
4
IN 7
5
+ 24V
6
IN 8
7
+ 24V
8
IN 9
9
+ 24V
10
IN 10
11
+ 24V
12
IN 11
13
+ 24V
14
IN 12
15
COM2
16
GND
Digital input 6-12
1
+ 24V
2
IN 6
3
+ 24V
4
IN 7
5
+ 24V
6
IN 8
7
+ 24V
8
IN 9
9
+ 24V
10
IN 10
11
+ 24V
12
IN 11
13
+ 24V
14
IN 12
15
COM2
16
GND
Digital input 6-12
1
+ 24V
2
IN 6
3
+ 24V
4
IN 7
5
+ 24V
6
IN 8
7
+ 24V
8
IN 9
9
+ 24V
10
IN 10
11
+ 24V
12
IN 11
13
+ 24V
14
IN 12
15
COM2
16
GND
Digital input 6-12
1
+ 24V
2
IN 6
3
+ 24V
4
IN 7
5
+ 24V
6
IN 8
7
+ 24V
8
IN 9
9
+ 24V
10
IN 10
11
+ 24V
12
IN 11
13
+ 24V
14
IN 12
15
COM2
16
GND
Digital input 6-12
1
+ 24V
2
IN 6
3
+ 24V
4
IN 7
5
+ 24V
6
IN 8
7
+ 24V
8
IN 9
9
+ 24V
10
IN 10
11
+ 24V
12
IN 11
13
+ 24V
14
IN 12
15
COM2
16
GND
Digital input 6-12
1
+ 24V
2
IN 6
3
+ 24V
4
IN 7
5
+ 24V
6
IN 8
7
+ 24V
8
IN 9
9
+ 24V
10
IN 10
11
+ 24V
12
IN 11
13
+ 24V
14
IN 12
15
COM2
16
GND
Valves
1
+ 24V
2
OUT 1
3
GND
4
+ 24V
5
OUT 2
6
GND
Valves
1
+ 24V
2
OUT 1
3
GND
4
+ 24V
5
OUT 2
6
GND
[page 7]
input OUT 2
4.5 Pneumatic connection
Also refer to paragraph 4.4.11.
4.5.1 Filter pressure sensor
To monitor the filter pressure, you must connect pneumatic
hoses to the internal filter pressure sensor (+ and –).
Fig. 4.32
• Connect the pneumatic hoses + and – to the corresponding
bulkhead connectors (B).
You must install the other sides of the pneumatic hoses to the
filter system (MDB or SCS). For connection of the hoses you
need the cable nuts supplied with the Panel

SlaveBoard cable (#1).
+
– +
–
+
–
+
–
In case of an MDB system:
• Proceed with paragraph 4.5.2
In case of an SCS system:
• Proceed with paragraph 4.5.3
4.5.2 MDB
The filter pressure sensor measures the pressure difference
between the filter compartment and the housing of the
compressed air tank.
Fig. 4.28
• Remove the cover caps from the + and – (A+B) on the
lower filter module.
• Install a cable gland in the + and – connection.
Fig. 4.28
A B C D
C
B
5
D
A
20
23
24
+ –
A B
+ –
+ and – connection
Fig. 4.30
• Remove the filter cap and install another cable gland inside
the filter module ( + ).
• (1) Put a pneumatic hose through the + connection.
• (2) Put the hose through the other cable gland into the
filter compartment.
• (3) Put the other hose through the – connection.
Fig. 4.29
+
+
–
1
2
3
Cable glands and pneumatic hoses
Fig. 4.30
• Make sure to have approx. 25 mm (1 in.) (A+B) hose end.
• Tighten all cable glands.
Fig. 4.30
+
+
–
A
B
Pneumatic hose ends
4.5.3 SCS
Fig. 4.31
• Connect the two pneumatic hoses to the corresp
and – (A+B) on the junction box.