manualshive.com logo in svg

Plextor 401240SE, Инструкция по установке и эксплуатации, Страница: 23 / 64

Поделиться
Скачать
Plextor 401240SE Скачать руководство пользователя страница 23

Section 2. Installing Your PlexWriter 

PlexWriter 40/12/40S Installation and Users Manual  

17

 

Setting Switches on a PlexWriter External SCSI Drive  

Use this procedure if you have a PlexWriter external SCSI drive. (However, if you 
already have a SCSI board installed, an external PlexWriter is the only SCSI 
peripheral you will use with your computer, and you do not need to change any 
settings, skip now to “Install a PlexWriter External SCSI Drive” on page 24.) 
 
Factory SCSI Switch Settings  
A rear-panel rotary dial controls the SCSI ID setting of the external PlexWriter drive, 
and other settings are controlled by DIP switches. Figure 9 shows the factory settings 
of the rear-panel dial and switches. 

 

 

Figure 9: Factory Settings for Dial and DIP Switches on External SCSI Drive 

 

CAUTION: Turn the drive’s power OFF before changing the setting of the SCSI ID 
dial or the DIP switches.  

 
Changing the SCSI ID 
If you already have another SCSI peripheral whose SCSI ID is set to 4, you must 
change the SCSI ID number of either that peripheral or that of the PlexWriter drive. 
(But see “Do I Have to Change My PlexWriter’s SCSI ID Number?” on page 10 
before proceeding.) 
 
To change the SCSI ID number of the external PlexWriter drive, rotate the dial’s 
arrow to a different SCSI ID number. 
 

Содержание 401240SE

































































Отзывы:

Нет отзывов