pleasant hearth PH35PS-B Скачать руководство пользователя страница 6

Страница: 6 / 44

7077-801F • 08/20

F. Mobile Home Approved

•

This appliance is approved for mobile home installations

when not installed in a sleeping room and when an

outside combustion air inlet is provided.

•

The structural integrity of the mobile home floor, ceiling,

and walls must be maintained.

•

The appliance must be properly grounded to the frame

of the mobile home with #8 copper ground wire, and use

only listed double-wall connector pipe.

•

Outside Air Kit provided with each unit must be installed

in a mobile home installation.

D. Glass Specifications

This appliance is equipped with 5mm ceramic glass.

Replace glass only with 5mm ceramic glass. Please

contact GHP for replacement glass.

E. Electrical Rating (On High)

WARNING

This product and the fuels used to operate this product (wood), and

the products of combustion of such fuels, can expose you to

chemicals including carbon black, which is known to the State of

California to cause cancer, and carbon monoxide, which is known to

the State of California to cause birth defects or other reproductive

harm. For more information go to: WWW.P65Warnings.ca.gov

NOTE:

This appliance is approved for installation in

a workshop.

Model

Electrical Rating

PH35PS-B

115 VAC, 60 Hz, Start 2.6 Amps,

Run 0.9 Amps

PH50PS-B

PH50CABPS-B

I. Sleeping Room

When installed in a sleeping room it is recommended that

3ft of vertical be installed prior to horizontally exiting the

room and a smoke/CO alarm be installed in the bedroom.

The size of the room must be at least 50ft³ per 1,000 Btu/hr

stove input, if the stove exceeds the room size, outside air

must be installed.

J. California - PROP65

G. Non-Combustible Materials

Material which will not ignite and burn, composed of any

combination of the following:

Steel

Plaster

Brick

Iron

Concrete

Tile

Glass

Slate

Materials reported as passing

ASTM E 136, Standard

Test Method for Behavior of Metals, in a Vertical Tube

Furnace of 750° C.

H. Combustible Materials

Material made of/or surfaced with any of the

following materials:

Wood

Compressed Paper

Plant Fibers

Plastic

Plywood/OSB

Sheet Rock (drywall)

Any material that can ignite and burn: flame proofed or not,

plastered or non-plastered.

WARNING

Risk of Fire.

GHP disclaims any responsibility for, and the

warranty and agency listing will be voided by

the below actions.

DO NOT:

•

Install or operate damaged appliance

•

Modify appliance

•

Install other than as instructed by the manufacturer.

•

Operate the appliance without fully assembling all

components

•

Over fire

•

Install any component not approved by the

manufacturer

•

Install parts or components not Listed or approved

•

Disable safety switches

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a

qualified installer, service agency or your dealer.

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды