pleasant hearth PH35PS-B Скачать руководство пользователя страница 25

Страница: 25 / 44

[email protected]

7077-801F • 08/20

4-1/2

[114]

23-3/4 [603]

23-3/16

[590]

35-1/2

[902]

D. Clearances to Combustibles (UL and ULC)

9-1/2

[241]

32-5/16

[821]

4-1/16

[103]

22-11/16 [576]

NOTE:

Turn to pages 29, 30 and 31 for side views and

more detailed images of clearances and installation

types.

* Follow pipe manufacture listed clearance

Vertical Installations (Interior Flue)

Straight Back Against Wall

Inches

Millimeters

Back Wall to Appliance

Back Wall to Flue Pipe

Side Wall to Appliance

330

Corner Installation

Inches

Millimeters

Walls to Appliance

Horizontal Flue Installations

Straight Back Against Wall

Inches

Millimeters

Back Wall to Appliance

Back Wall to Flue Pipe

Side Wall to Appliance

330

C. Appliance Dimensions: PH50CABPS-B

•

Do NOT connect this unit to a chimney flue servicing

another appliance.

•

Do NOT connect to any air distribution duct or system.

CAUTION

WARNING

HOT SURFACES!

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

•

Do not touch glass until it is cooled

•

NEVER allow children to touch glass

•

Keep children away

•

CAREFULLY SUPERVISE children in same room

as fireplace.

•

Alert children and adults to hazards of

high temperatures.

• High temperatures may ignite clothing or other

flammable materials.

•

Keep clothing, furniture, draperies and other

flammable materials away.

Содержание PH35PS-B













































Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды

pleasant hearth PH35PS-B, Руководство пользователя

Результаты поиска

Содержание PH35PS-B

Отзывы:

Похожие инструкции для PH35PS-B

Бренды по названию

Популярные бренды