manualshive.com logo in svg

Playcore SPECTRUM Aquatics Motion Trek 400, Руководство пользователя

Поделиться
Скачать
Playcore SPECTRUM Aquatics Motion Trek 400 Скачать руководство пользователя страница 12

11 

800.791.8056 

▪

 www.spectrumproducts.com 

Plug the battery charger into a standard electrical outlet*.  The green LED on the charger will 
light up, indicating that the charger is on.  

Plug the charging cable into the charging port on the battery cradle. Place battery in charging 
cradle. If the battery is up to the charged voltage, the LED on the charger will stay green. If the 
charger determines that the battery needs to be charged, the LED on the charger will change to 
red. 

The red LED will turn green when the battery is fully charged.  This charger has internal 
monitoring circuitry that will not overcharge the battery, if the battery is left on the charger for 
extended periods of time the charger will go into short charging cycles at intervals to keep the 
charge level at optimal. 

*Charger accepts 110 VAC

When the battery is fully charged, remove it from the charging cradle and install the battery on 
the lift. The Battery Capacity Indicator on the receiver will show a green LED, indicating that the 
battery is fully charged and installed properly. When the LED changes to amber the lift is still OK 
to use. However when the LED changes to red, or an audible tone is heard during a lift cycle, 
the battery pack needs to be recharged.   

To keep the battery from discharging to the point of causing damage, it is important to 
charge the battery at least once monthly, even if the battery has not been installed on the 
lift.  

After initial break in, the battery should last approximately 90 cycles at the full 350-lb load rating 
of the lift before it needs recharging. The battery will need to be replaced after 500 to 800 
charge cycles or three to four years if properly maintained (approximately 20,000 lifting cycles). 

Care and Maintenance 

The following should be performed periodically to ensure safe and dependable use. 

1. Remove any discoloration with a 3M scratch pad (stainless steel components only).

Wipe clean with a sponge dampened with Spectra Clean. Repeat these steps several
times to passivate the stainless steel. Lift maintenance kits are available from Spectrum
(Part Number 152161-MT). Do not spray with high-pressure water, only clean with non-
chlorinated water.

2. Check all electrical connections – Check any external electrical cables for wear and/or

breakage in the outer insulation.

3. Check all mechanical connections – inspect the Nylock nuts on all moving parts and

make sure they are snug. Lubricate all pivot points with light oil (3-1).

4. To maintain the battery properly, the battery must be fully charged monthly. If the battery

goes for longer than three months without a charge, the battery will have significantly
reduced capacity.

Содержание SPECTRUM Aquatics Motion Trek 400














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды