T568B is electrically identical to T568A but swaps
the green and orange pairs. Either standard will
work as long as the same standard is used at both
ends of a run or patch cable. Mixing “A” and “B”
creates a cross-over cable.
The 1–2 pair pins are shorted together, and the
7–8 pair is open. The pins with the errors are
flashing. Dash lines (-) on the bottom (remote)
display line indicate the short, while no numbers
on the bottom line indicate the open pair.
1 and 2 pins on the MapMaster mini are con-
nected to pins 2 and 1 at the remote-end. The
pins with this error are flashing. The “U” for the
remote pin numbers indicates an unrecognizable
continuity was detected that is neither a short or
open. An ID remote connected to the MapMaster
mini when in cable test mode would also show
this error.
A common error in building a cable is to put all
the pairs in pin sequence 1–2, 3–4, 5–6 and
7–8. This will produce the correct continuity,
but the pairs are designated to be on pins 3–6
and 4–5 in the middle of the connector for
compatibility with phone wiring. This wiring error
is only detected by the split pair test since the
designated pairs are not twisted together.
•
Locate:
Detects network map-only ID remotes #1–#5.
This mode is not used to test cables but is used only to
map the location of the jack that the far end is connected
to using the map-only ID remotes. For testing cables use
the master remote stored in the bottom of the tester.
•
Hi Lo 1, Hi Lo 2, Hi, Lo
(four tone cadences): The four
modes are all tone generator modes with different
sounds. The “Hi Lo” tones are made up of two frequencies
with different timings. “Hi” and ”Lo” are single frequency.
Once in a tone mode, short presses change the pins
carrying tone. The pins with tone are displayed. In a tone
mode, the tester will turn off automatically 30 minutes
after the last button press or by exiting to mode select
with a long press. Note that you must use an analog tone
probe to hear the tones generated by the tester.
•
Off
: When the button is released with “OFF” displayed,
the Tester will power off. Once in one of the above
modes, OFF is the first mode offered upon exiting to
mode select. To select a different mode other than OFF,
continue to hold the button down and the next mode in
rotation will be displayed next.
•
Cable
: The cable test mode is the single cable test mode
with 20 second timeout that a short press from powered
off executes.
Warranty
Platinum Tools warrants this product to be free from defects
in material and workmanship for 12 months for test equip-
ment and 3 months for cables and accessories from the date
of purchase. Liability is limited to the repair and or replace-
ment of the product. Warranty excludes batteries and wear-
able components such as the integrated RJ45 jack included
with the product. NO IMPLIED WARRANTIES OF MERCHANT-
ABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Platinum
Tools is not liable for consequential damages.
Should any parts or workmanship prove defective, Platinum
Tools will repair or replace at Platinum Tools’ option, at no
cost to the Buyer except for shipping costs from the Buyer’s
location to Platinum Tools. This is Buyer’s SOLE AND EXCLU-
SIVE REMEDY under this Agreement. This warranty does not
apply to products which have been subject to neglect, ac-
cident or improper use, or to units which have been altered
or repaired by other than an authorized repair facility.
Cleaning
Turn off the MapMaster mini and disconnect all cables. Use
a damp, clean cloth to clean the MapMaster mini. CAUTION:
do not use abrasive or harsh cleaners or solvents.
Storage
When the MapMaster mini is not in use, store in a dry,
protective case. Batteries should be removed if stored for a
long period of time. Do not expose to high temperatures or
humidity. When stored in temperatures exceeding the limits
listed in the Specifications section, allow the MapMaster
mini to return to normal recommended operating conditions
before using it.
Disposal
Caution: This symbol indicates that equipment and its
accessories should be treated to a separate collection and
proper disposal.
Warning
Always wear approved eye protection. Do NOT use on
live circuits
Tester
Tester
Tester
Tester
Remote
Remote
Remote
Remote
Properly Wired T568A UTP:
T568A Cable with a Short and Open:
T568A Cable with a Misfire and
Unrecognized Continuity:
T568A Cable with Split Pairs:
WIRING AND DISPLAY EXAMPLES
WIRING AND DISPLAY EXAMPLES
Test Equipment Depot - 800.517.8431
99 Washington Street, Melrose, MA 02176
TestEquipmentDepot.com
