PlasmaPart PlasmaOne 50A Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 15

PlasmaPart PlasmaOne 50A Скачать руководство пользователя страница 6

Declaration of Conformity

PlasmaPart CUT 50 PlasmaOne

Manufacturer:

ZHEJIANG ZHONGJIAN (ZOJAN) WELDING EQUIPMENT CO.,LTD

Address: South Of Jiulong Rd., Industrial City, Wenling, Zhejiang, China

Tel.:86-576-81667866

PlasmaPart Limited

Unit 1 Debdale Lane

Keyworth

Nottinghamshire

NG12 5HN

0844 822 80 40

The equipment described in this manual conforms to all applicable aspects and regulations
of the Low Voltage Directive and to the national legislation for the enforcement of this
directive.

The equipment described in this manual conforms to all applicable aspects and regulations
of the EMC directive and to the national legislation for the enforcement of this directive.

PlasmaPart machines are the result of extensive and continuous product development. Our
manufacturing process is two-part and once the base units arrive at our facilities they are
completed to our specification in the UK. Each machine is individually tested and verified
before completion, ensuring the product is safe for use when used in accordance with these
instructions.

PlasmaPart are committed to continual development and improvement of our products, if
you have any comments, concerns, or suggestions please do not hesitate to contact us.

«
...
4
5
6
7
8
...
»

Содержание PlasmaOne 50A
















Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды