manualshive.com logo in svg

PlasmaPart IndustriCut 100A, Инструкция по эксплуатации и безопасности

Поделиться
Скачать
PlasmaPart IndustriCut 100A Скачать руководство пользователя страница 6

Declaration of Conformity  

PlasmaPart 100A IndustriCut 

Manufacturer:

 

 ZHEJIANG ZHONGJIAN (ZOJAN) WELDING EQUIPMENT CO.,LTD 

Address: South Of Jiulong Rd., Industrial City, Wenling, Zhejiang, China 

Tel.:86-576-81667866 

 

PlasmaPart Limited 

Unit 1 Debdale Lane 

Keyworth 

Nottinghamshire 

NG12 5HN 

0844 822 80 40 

 

The equipment described in this manual conforms to all applicable aspects and regulations 
of the Low Voltage Directive and to the national legislation for the enforcement of this 
directive. 

The equipment described in this manual conforms to all applicable aspects and regulations 
of the EMC directive and to the national legislation for the enforcement of this directive. 

 

 

PlasmaPart machines are the result of extensive and continuous product development. Our 
manufacturing process is two-part and once the base units arrive at our facilities they are 
completed to our specification in the UK. Each machine is individually tested and verified 
before completion, ensuring the product is safe for use when used in accordance with these 
instructions. 

PlasmaPart are committed to continual development and improvement of our products, if 
you have any comments, concerns, or suggestions please do not hesitate to contact us. 

Содержание IndustriCut 100A
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды