background image

Plantronics Savi User Guide

10

out of range warning

If you are on a call, you will hear the audio degrade as you move 
out of range. 

If you stay out of range, active calls will be suspended. Calls will 
be re-established when you walk back into range. 

Low battery warning

A repeating high/low tone pair every 10 seconds indicates the 
battery is low. You should recharge the headset immediately. 

Checking battery level

You can check the battery level by moving the call control button 
to the volume down position, then pressing inwards and holding 
for two seconds. The headset indicator will flash red to indicate 
the remaining battery charge level.

One red flash = low charge level 
Two red flashes = medium charge level 
Three red flashes = high charge level 

turning headset indicator blue flash on/off

By default, the headset indicator flashes blue to indicate the 
headset state as described in the section 

Headset indicator 

lights and tones

. This feature may be disabled by moving the call 

control button to the volume up position, then pressing inwards 
and holding for two seconds. The headset indicator will show a 
short burst of blue flashes.

Repeat this operation to turn the headset blue flashing indicator 
back on.

mute warning

When mute is activated, you will hear a single low tone which will 
repeat every 30 seconds. 

Pairing headset to USB adapter

The headset and USB adapter are supplied paired to each other. 
However, if you wish to use a replacement headset with your 
existing USB adapter, the units can be paired to each other by the 
following method:

1

  Ensure your replacement headset is fully charged.

2

  Power the headset off by pressing and holding the call 

control button for six seconds. 

The headset indicator light 

will be red for four seconds.

3

  Place the headset in pairing mode by pressing and 

holding the call control button until the indicator light 
flashes red and blue.

4

  Place the USB adapter in pairing mode by pressing 

and holding the pairing button on the adapter for two 
seconds. 

The pairing light will flash red and blue.

5

  When the pairing light on the USB adapter goes solid 

blue, the headset and the USB adapter are paired.

 

notE:

 Take care when pairing the USB adapter. Do not press 

hard. Please “press” with both fingers rather than push on the 
USB adapter to avoid damage to the USB adapter or USB port.

Содержание Savi Go WG100/B


















Отзывы: