Planmeca Compact i3 Скачать руководство пользователя страница 91

Страница: 91 / 106

3. Connect the Morita micromotor hose to the apex locator housing

assembly (1) and the instrument console, and then connect the

micromotor.

4. Test the apex locator function as described in section "Testing apex

locator function" on page 87.

16.4.3 Testing apex locator function

About this task

The apex locator function must be tested weekly.

NOTE

While the test is going on, the dental unit's control panel is locked.

Steps

1. Open the

Apex locator window on the control panel either by pressing

the Apex locator button or by activating the Morita micromotor and

selecting one of the apex presets (a1 - a3).

NOTE

If the Apex locator button is not visible in your control panel's swipe

menu, you must add it. For instructions, see your Planmeca dental unit's

user's manual, section

Organising items on control panel.

16 Installing instruments

Installation manual

Planmeca Compact i3 87

Содержание Compact i3











































































































Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды

Planmeca Compact i3, Руководство по установке

Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды