Planmeca Compact i3 Скачать руководство пользователя страница 85

Страница: 85 / 106

16 Installing instruments

The positions of the instruments are completely user dependent. The only

instrument, which has fixed position is the syringe. The syringe must be

positioned next to the control panel i.e. to the leftmost position.
The microprocessor control logic automatically identifies the instrument hose

in each position. This enables the instrument positions to be rearranged

afterwards without any reprogramming.

NOTE

Please note that you don’t have to attach instrument hoses (or instrument

arms/holders) to all positions.

16.1 Attaching balanced instrument arms

Attach the instrument arms (1) to the back side of the instrument console by

pushing them firmly into position.

16 Installing instruments

Installation manual

Planmeca Compact i3 81

Содержание Compact i3











































































































Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды

Planmeca Compact i3, Руководство по установке

Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды