Planmeca Compact i3 Скачать руководство пользователя страница 14

Страница: 14 / 106

Changes to the network

Changes to the network could introduce risks requiring additional analysis.

Connection to networks including other equipment could result in previously

unidentified risks to patients, operators or third parties. The user

organisation is responsible for identifying, analysing, evaluating and

controlling these risks.
Changes to the IT-NETWORK include:
•

Changes in network configuration

•

Connection of additional items

•

Disconnection of items

•

Update of equipment

•

Upgrade of equipment

2.6 Patient area

The patient area is 1.5 m (59.1”) in each direction from the dental unit.

CAUTION

Use only Planmeca specified devices inside the patient area.

CAUTION

The floor of the patient area must be dry.

NOTE

Connect only Planmeca specified devices to the dental unit.

NOTE

The external PC must be protectively earthed and IEC 60950 -approved (CE

marked).

NOTE

The monitor must fulfil IEC 60601-1 ed.3 requirements.

2 Pre-installation requirements

10 Planmeca Compact i3

Installation manual

Содержание Compact i3











































































































Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды

Planmeca Compact i3, Руководство по установке

Результаты поиска

Содержание Compact i3

Отзывы:

Похожие инструкции для Compact i3

Бренды по названию

Популярные бренды