Planet WDAP-1800AX Скачать руководство пользователя страница 94

Страница: 94 / 125

User Manual of WDAP-C1800AX &WDAP-1800AX

- 65 -

NTP Client Update

Once this function is enabled, router will automatically update current

time from NTP server.

NTP Server

User may use the default NTP sever or input NTP server manually.

4.5.3 Saving/Restoring Configuration

This page shows the status of the configuration. You may save the setting file to either USB storage or

PC and load the setting file from USB storage or PC as

Figure 4-58

is shown below:

Figure 4-58:

Save/Restore Configuration

■

Save Setting to PC

Object

Description

Configuration Export

Press the

button to save setting file to PC.

Configuration Import

Press the

button to select the setting file, and then

press the

button to upload setting file from PC.

4.5.4 Firmware Upgrading

This page provides the firmware upgrade of the router as shown in

Figure 4-59.

Содержание WDAP-1800AX






























































































































Результаты поиска

Содержание WDAP-1800AX

Отзывы:

Planet WDAP-1800AX, Руководство пользователя, Страница: 94 / 125

Результаты поиска

Содержание WDAP-1800AX

Отзывы: