Planet IFGS-1022HPT Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 24

Planet IFGS-1022HPT Скачать руководство пользователя страница 9

9

2. Tighten the wire-clamp screws for preventing the wires from loosening.

1

2

3

4

5

6

Power 1

Fault

Power 2

+

-

+

-

Note

1.

The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.

2.

The DC power input range is 48V ~ 56V DC.

2.6 Wiring the Fault Alarm Contact

The fault alarm contacts are in the middle of the terminal block connector as the
picture shows below. Inserting the wires, the Industrial PoE+ Switch will detect
the fault status of the power failure and then forms an open circuit. The following
illustration shows an application example for wiring the fault alarm contacts.

Fault Alarm Contacts

The Fault Alarm Contacts are

energized (CLOSE) for normal

operation and will OPEN when

failure occurs

Fault

Insert the wires into the fault alarm contacts

Note

1.

The wire gauge for the terminal block should be in the range
between 12 and 24 AWG.

2.

Alarm relay circuit accepts up to 30V, max. 3A currents.

«
...
7
8
9
10
11
...
»

Содержание IFGS-1022HPT

























Отзывы:

Нет отзывов