Planet ICA-120 Скачать руководство пользователя страница 7

Страница: 7 / 77

2. Basic Setup

This chapter provides details of installing and configuring the Internet Camera

2.1 System Requirements

Network Interface

10/100MBase-TX Ethernet

Monitoring System Recommended for Internet Explorer 6.0 or later

System Hardware

· CPU: Pentium 4, 3.0GHz or above

· Memory Size : 512 MB (512 MB or above Recommended )

· VGA card resolution : 1024 x 768 or above

· VGA card memory : 64 MB or above

· Network bandwidth: In VGA resolution mode, minimum

upload bandwidth is 1Mbps.

NOTE:

The listed information is minimum system requirements only. Actual requirement will

vary depending on the nature of your environment.

2.2 Physical Description

2.2.1 Front View

Internal

Microphone

Lens

Lens

User could adjust the focus to get the best picture quality.

Internal
Microphone

The Camera has built-in an internal microphone. This microphone is
hidden in the pinhole located on the front panel

Содержание ICA-120














































































Результаты поиска

Содержание ICA-120

Отзывы:

Бренды по названию

Популярные бренды

Planet ICA-120, Руководство пользователя

Результаты поиска

Содержание ICA-120

Отзывы:

Бренды по названию

Популярные бренды