Planet FSD-803PE Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 24

Planet FSD-803PE Скачать руководство пользователя страница 13

11

Chapter 4

CONNECTING THE SWITCH

TThis chapter describes how to connect the Switch to your Fast Ethernet network.

PC to Switch

A PC can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight
cable. The PC (equipped with a RJ-45 10/100Mbps phone jack) should be connected to
any of the 8 numbered port.

The LED indicators for PC connection depend on the LAN card capabilities. If LED
indicators are not light after making a proper connection, check the PC LAN card, the
cable, the Switch conditions and connections.

The following are LED indicator possibilities for a PC to Switch connection:

• The LINK/ACT and 100 LED indicators light green for hookup to 100Mbs.

• LNK/ACT lights green, while 100 LED off for hookup to 10Mbps speed.

Hub to Switch

A hub (10 or 100Base-TX) can be connected to the Switch via a two-pair Category 3, 4, 5
UTP/STP straight or crossover cable. The connection is accomplished from the hub Uplink
(MDI-X) or normal (MDI) port to any of the Switch (MDI/MDI-X) ports:

A. 10Base-T Hub

For a 10Base-T hub, the Switch LED indicators should light up as the following:

100 LED indicator is OFF.

LNK/ACT LED indicator lights green.

B. 100Base-TX Hub

For a 100Base-TX hub, the Switch LED indicators should light up as the follow-
ing:

LNK/ACT,100 LED indicators light green.

10-000039-000.indd

2004/8/27, �� 05:37

11

«
...
11
12
13
14
15
...
»

Содержание FSD-803PE

























Отзывы:

Нет отзывов