manualshive.com logo in svg

Planet FSD-1020, Руководство пользователя

Поделиться
Скачать
Planet FSD-1020 Скачать руководство пользователя страница 3

 

 

Trademarks 

Copyright 

 PLANET Technology Corp. 1998. 

Contents subject to revision without prior notice. 
PLANET is a registered trademark of PLANET Technology Corp.  All 
other trademarks belong to their respective owners.

 

 

FCC Warning 

The device has been tested and found to comply with limits for a Class 
A digital device, pursuant to Part 15 of the FCC Rules. These limits are 
designed to provide reasonable protection against harmful interference 
when the equipment is operated in a commercial environment. This 
equipment generates, uses and can radiate radio frequency energy and, if 
not installed and used in accordance with the user’s manual, may cause 
interference in witch case user will be required to correct the 
interference at his own expense.  

 

CE Mark Warning 

This is a Class A product.  In a domestic environment this product may 
cause radio interference in which case the user may be required to take 
adequate measures. 

 

Reversion  

User's manual for PLANET Desktop Switch 
Models: FSD-1020 
Rev: 1.0 (Feb. 1998) 

Part No. EMHFSD1020 

 

 

 

 

Содержание FSD-1020























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды