- 9 -
- 10 -
- 11 -
- 12 -
- 13 -
- 14 -
Step 4:
Connect your Fast Ethernet Switch to network
devices.
A.
Connect one end of a standard network cable
to the 10/100 RJ45 ports on the front of the
Fast Ethernet Switch.
B.
Connect the other end of the cable to the
network devices such as printer servers,
workstations or routers.
Step 5:
Supply power to the Fast Ethernet Switch.
A.
Connect one end of the power cable to the Fast
Ethernet Switch.
B.
Connect the power plug of the power cable to
a standard wall outlet.
When the Fast Ethernet Switch receives power, the Power
LED should remain solid green.
Step 3:
Secure the brackets tightly.
Step 4:
Follow the same steps to attach the second
bracket to the opposite side.
Step 5:
After the brackets are attached to the Fast
Ethernet Switch, use suitable screws to securely
attach the brackets to the rack, as shown in Figure
4.
FNSW-4800
48-Port 10/100M
bps Fast Eth
ernet Swi
tch
PWR
1 5 9 13 17
21 25 29 33 37
41 45
2 6 10 14
18 22 26 30
34 38 42 46
3 7 11 15 19
23 27 31 35
39 43 47
4 8 12 16
20 24 28 32 36
40 44 48
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
ACT
LNK
Figure 4:
Mounting the Fast Ethernet Switch on a Rack
Step 6:
Proceed with Steps 4 and 5 of
Department
Networking Installation
to connect the network
cabling and supply power to your Fast Ethernet
Switch.
Rack Mounting
To install the Fast Ethernet Switch in a 19-inch standard
rack, follow the instructions described below.
Step 1:
Place your Fast Ethernet Switch on a hard flat
surface, with the front panel positioned towards
your front side.
Step 2:
Attach a rack-mount bracket to each side of the
Switch with supplied screws attached to the
package. Figure 3 shows how to attach brackets to
one side of the Fast Ethernet Switch.
FNSW-4800
48-Port 10/100Mbps Fast Ethe
rnet Switch
PWR
1 5 9 13
17 21 25 29
33 37 41 45
2 6 10 14
18 22 26 30
34 38 42 46
3 7 11 15
19 23 27 31
35 39 43 47
4 8 12 16
20 24 28 32
36 40 44 48
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
ACT
LNK
Figure 3:
Attaching the brackets to the Fast Ethernet Switch
Caution
You must use the screws supplied with the
mounting brackets. Damage caused to
the parts by using incorrect screws would
invalidate your warranty.
Customer Support
Thank you for purchasing PLANET products. You can browse
our online FAQ resource at the PLANET Web site first to
check if it could solve your issue. If you need more support
information, please contact PLANET switch support team.
PLANET online FAQ:
http://www.planet.com.tw/en/support/faq.php?type=1
Switch support team mail address:
[email protected]
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other
trademarks belong to their respective owners.
EC Declaration of Conformity
For the following equipment:
*Type of Product: 48-Port 10/100Base-TX Fast Ethernet Switch
*Model Number: FNSW-4800
* Produced by:
Manufacturer‘s Name :
Planet Technology Corp.
Manufacturer‘s Address: 10F., No.96, Minquan Rd., Xindian Dist.,
New Taipei City 231, Taiwan (R.O.C.)
is herewith confirmed to comply with the requirements set out in the Council Directive on the
Approximation of the Laws of the Member States relating to Electromagnetic Compatibility
Directive on (2004/108/EC).
For the evaluation regarding the EMC, the following standards were applied:
EN55022
(2010 + AC:2011)
EN 61000-3-2
(2006+A1:2009+A2:2009)
EN 61000-3-3
(2013)
EN55024
(2010)
IEC
61000-4-2 (2008)
IEC
61000-4-3 (2010)
IEC
61000-4-4 (2012)
IEC
61000-4-5 (2005)
IEC
61000-4-6 (20
13
)
IEC
61000-4-8 (2009)
IEC
61000-4-11 (2004)
EN60950-1
(2006 + A11:2009 + A1:2010 +
A12:2011)
Responsible for marking this declaration if the:
Manufacturer
Authorized representative established within the EU
Authorized representative established within the EU (if applicable):
Company Name:
Planet Technology Corp.
Company Address: 10F., No.96, Minquan Rd., Xindian Dist., New Taipei City 231, Taiwan
(R.O.C.)
Person responsible for making this declaration
Name, Surname
Kent Kang
Position / Title :
Product Manager
Taiwan 16
th
Jan., 2014
Place
Date
Legal Signature
PLANET TECHNOLOGY CORPORATION
e-mail: [email protected] http://www.planet.com.tw
10F., No.96, Minquan Rd., Xindian Dist., New Taipei City, Taiwan, R.O.C. Tel:886-2-2219-9518 Fax:886-2-2219-9528