Planet Networking & Communication WNRT-617 Скачать руководство пользователя страница 104

Страница: 104 / 155

User’s Manual of WNRT-617

-97-

Click the

Disable All

button to disable all the entries.

Click the

Delete All

button to delete all the entries.

Click the

Previous

button to view the information in the previous screen, click the

Next

button to view

the information in the next screen.

5.12.2 System Routing Table

Choose menu “

System Routing Table

”, you can check all of the valid route entries in use. The

Destination IP address, Subnet Mask, Gateway, and Interface will be displayed for each entry. Click

the

Refresh

button to refresh the data displayed.

Figure 5-68

5.13 Bandwidth Control

There are two submenus under the Bandwidth Control menu as shown in

Figure 5-52

. Click any of

them, and you will be able to configure the corresponding function. The detailed explanations for each

submenu are provided below.

Figure 5-52

Содержание WNRT-617




























































































































































Результаты поиска

Содержание WNRT-617

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication WNRT-617, Руководство пользователя

Результаты поиска

Содержание WNRT-617

Отзывы:

Бренды по названию

Популярные бренды