Planet Networking & Communication WDAP-C7200E Скачать руководство пользователя

Страница: 37 / 85

User Manual of WDAP-C7200E

-30-

The page includes the following fields:

Object

Description

WLAN

Select “

” or “

OFF

” to enable or disable 2.4G or 5.8G wireless LAN.

Wireless Analyzer

Press the button to check your wireless environment.

Status SSID

It is the wireless network name. The default SSID is

“

PLANET_2.4G

” or

“

PLANET_5G

”.

Channel

Select the operating channel you would like to use. The channel range will be

changed by selecting a different domain.

Encryption

Select the wireless encryption. The default is “

None

”.

AP Name

Enter the name of AP.

AP Location

Enter the location of AP.

Enter the LAN IP address.

Figure 5-13

AP Mode -- LAN

Содержание WDAP-C7200E






















































































Результаты поиска

Содержание WDAP-C7200E

Отзывы:

Похожие инструкции для WDAP-C7200E

Бренды по названию

Популярные бренды

Planet Networking & Communication WDAP-C7200E, Руководство пользователя

Результаты поиска

Содержание WDAP-C7200E

Отзывы:

Похожие инструкции для WDAP-C7200E

Бренды по названию

Популярные бренды