- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET IEEE 802.3at High
Power over Ethernet Injector, POE-163/POE-164.
Model LAN Port Speed PoE Standard PoE Budget
POE-163 10/100/1000Mbps 802.3at /
802.3af
30 watts
POE-164 10/100Mbps
“802.3at PoE Injector”
used in this user’s manual
refers to the POE-163/POE-164.
Unpack the box of the IEEE 802.3at High Power
over Ethernet Injector carefully and the box should
contain the following items:
The IEEE 802.3at High Power over Ethernet
Injector x 1
User’s Manual x 1
AC Power Cord x 1
If any of these are missing or damaged, please
contact your dealer immediately. If possible, retain
the carton including the original packing material,
and use them again to repack the product in case
there is a need to return it to us for repair.
2. Product Features
Interface
2-port RJ45 interfaces
1-port Data + Power output
1-port Data input
1 AC 100-240V input power socket
Power over Ethernet
High Power over Ethernet Mid-span PSE
IEEE 802.3at PoE Plus compliant
Backward compatible with IEEE 802.3af PD
device
Supports PoE Power up to 30 watts for PoE port
Auto-detects PoE IEEE 802.3at / 802.3af equip-
ment and devices for preventing damage from
incorrect installation
Remote power feeding up to 100m
Hardware
Plastic case
LED indicators for Power LED and Active LED
(PoE ready-in-use)
Standard Compliance
IEEE 802.3 10BASE-T
IEEE 802.3u 100BASE-TX
IEEE 802.3ab 1000BASE-T (POE-163 only)
IEEE 802.3af Power over Ethernet (802.3at
Type 1)
IEEE 802.3at Power over Ethernet (802.3at
Type 2)
FCC Part 15 Class B, CE
Note
PSE (Power Sourcing Equipment)
is
a device (switch, or hub for instance)
that will provide power in a PoE setup.
The maximum continuous output power
allowed for each IEEE 802.3at/IEEE
802.3af device is 30W/15.4W.
PDs (Powered Devices)
like IP
phones, network cameras and wireless
access points, etc. are PoE-enabled
terminals and thus they are power
sourcing equipment (PSE).
3. Product Specifications
Product
POE-163
POE-164
Hardware Specifications
Interface
“Data” Input
Port
1 x RJ45 STP
“PoE (Data
+ Power)”
Output Port
1 x RJ45 STP
AC Input
Power Socket 1
LED Indicator
System: Power x 1 (Green)
PoE Port: Active, PoE ready / In
Use x 1 (Green)
Network Cable
10BASE-T: 2-pair UTP Cat. 3, 4,
5, up to 100m (328ft)
100BASE-TX: 2-pair UTP Cat. 3,
4, 5, up to 100m (328ft)
1000BASE-T: 2-pair UTP Cat. 5,
5e, 6 up to 100m (328ft)
(POE-163 only)
EIA/TIA-568 100-ohm STP
(100m)
Data Rate
10/100/1000Mbps 10/100Mbps
Dimensions (W x D x H) 115 x 62.5 x 31 mm
Weight
177g
Unit Output Voltage
DC 53V, 0.6A
Power Requirements
100-240V AC, 50/60Hz, 0.75A
Power Consumption
30 Watts max.
Number of devices that
can be powered
1
Operating Temperature 0 ~ 50 degrees C
Storage Temperature
-10 ~ 70 degrees C
Operating Humidity
5 ~ 95%, relative humidity, non-
condensing
Storage Humidity
5 ~ 95%, relative humidity, non-
condensing
Power over Ethernet
PoE Standard
IEEE 802.3at Power over Ethernet
Plus / Mid-span PSE
PoE Power Output
DC 53V / 30 Watts
PoE Power Supply Type Mid-span
Power Pin Assignment 4/5(+), 7/8(-)
Standards Conformance
Standards Compliance
IEEE 802.3 10BASE-T Ethernet
IEEE 802.3u 100BASE-TX Fast
Ethernet
IEEE 802.3ab 1000BASE-T Gigabit
Ethernet
(POE-163 only)
IEEE 802.3af Power over Ethernet
(802.3at Type 1)
IEEE 802.3at Power over Ethernet
(802.3at Type 2)
Regulation Compliance FCC Part 15 Class B, CE
4. Product Outlook
Figure 1: shows an overview of the 802.3at PoE
Injector.
Rear Panel
Front Panel
Top Panel
Botton
Rear Panel
Front Panel
Top Panel
Botton
Figure 1:
POE-163 / POE-164 Outlook
LED Indicators
LED Color
Function
POWER Green
Lights to indicate that the 802.3at PoE
Injector has power.
ACTIVE Green
Lights off
to indicate the port is not
providing 53V DC in-line power.
Lights to indicate the port is providing
53V DC in-line power.
5. Hardware Installation
The following section describes the hardware
features of the 802.3at PoE Injector. Before
connecting any network device to the 802.3at PoE
Injector, read this chapter carefully.
This POE-163 provides three different running
speeds – 10Mbps / 100Mbps / 1000Mbps and the
POE-164 provides two different running speeds
– 10Mbps / 100Mbps in the same device for
automatically distinguishes the speed of incoming
connection. Please refer to following sections for
detailed information about the IEEE 802.3at Power
over Ethernet Injector.
5-1 Before Installation
Before your installation, it is recommended to check
your network environment. If there is any IEEE
802.3at devices that need higher power to power
on and work normally, the 802.3at PoE Injector
can provide you with power for this Ethernet device
easily. The 802.3at PoE Injector is equipped with an
AC power cord with 100-240V AC input and injects
DC 53V power into the pin of the twisted-pair cable
(pair 4, 5 [+] and pair 7, 8 [-] ).
If a power socket for the AC-DC adapter of your non
IEEE 802.3at networked device is not available, the
802.3at PoE Injector and POE-162S can provide you
with DC power for this Ethernet device easily.
Note
The 802.3at PoE Injector and POE-162S
can be installed in pair. However, the
use of third-party device is allowed if
the device complied with IEEE 802.3at
Power over Ethernet.
The 802.3at PoE Injector Installation
1. Connect the AC power cord to the “AC slot” of the
802.3at PoE Injector; the “POWER” LED will be
steadily on.
2. Connect a standard network cable from a switch /
workstation to the “LAN” port of the 802.3at PoE
Injector.
3. And connect the Injector to a remote device like a
PoE PTZ IP camera over the UTP cable.
** The 802.3at PoE Injector can directly connect
with any IEEE 802.3at / 802.3af end-nodes, such
as PTZ IP and speed dome cameras, color touch-
screen Voice over IP (VoIP) telephones, multi-
channel wireless LAN access points, etc. The
installation is shown in Figure 2 below.
