Planet Networking & Communication ICA-1200 Скачать руководство пользователя страница 13

Страница: 13 / 92

Full HD PoE/ Wireless Cube IP Camera

ICA-1200/W1200

Interface

Description

IR or Red-light LEDs

These LEDs are Infra-Red type by mode. It’s very useful for
low-lux environment to provide extra light source for image
sensor.

Lens & focus ring

User could use this ring to adjust focus manually.

Microphone

The Camera has built in an internal microphone. This
microphone is hidden in the pinhole located on the front panel.

PIR Sensor

PIR sensor is used to sense motion or detect whether a
human has moved in or out of the sensors range.

Micro-SD

User can insert a micro SD card into this slot for event
recording.

Speaker

The Camera has built in a speaker. This speaker allows to
output voice or alerting sound.

Antenna

User can attach the included antenna to antenna connector
(SMA type) or use another high-gain antenna to get higher
performance.

Содержание ICA-1200





























































































Результаты поиска

Содержание ICA-1200

Отзывы:

Похожие инструкции для ICA-1200

Бренды по названию

Популярные бренды

Planet Networking & Communication ICA-1200, Руководство пользователя

Результаты поиска

Содержание ICA-1200

Отзывы:

Похожие инструкции для ICA-1200

Бренды по названию

Популярные бренды