This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each receiver unit
(firing group). Set all parameters on the transmitter unit.
7. M: Wireless Flash Shooting with Manual Flash
Setting the flash mode to
1
<M>.
Taking the picture.
3
Setting <M> Flash Mode
You can directly operate the receiver unit to manually set the manual
flash or stroboscopic flash.
Setting the receiver unit.
1
Setting flash mode to <M>.
2
●
Press <
MODE
> button so
that <
M
> is displayed.
●
Set the manual flash
output. (Page 1
3
)
Setting flash
2
output.1/2/3/4<M/A/B/C>
●
Press Function Button 3
<
>. Turn the Select
Dial to set the flash output
of the groups. Press Set
Button to confirm.
Gr
●
Each group fires at the set
flash ratio.
8
.
Multi: Wireless Flash Shooting with Manual Flash
Setting <Multi> stroboscopic
flash.
●
Press <
MODE
> button so
that <
Multi
> is displayed.
●
Setting the stroboscopic
flash. (Page
14
)
Other Applications
If the camera has a depth-of-field preview button, pressing it will fire
the flash continuously for 1 second. This is called modeling flash.
Sync Triggering
The Sync Cord Jack is a Φ2.5mm plug. Insert a trigger plug here
and the flash will be fired synchronously with the camera shutter.
Modeling Flash
It enables you to see the shadow effects on the subject and the
lighting balance. You can fire the modeling flash during wireless or
normal flash shooting.
●
To avoid overheating and deteriorating the flash head, do
not fire the modeling flash for more than 10 consecutive
times. If you fire the modeling flash 10 consecutive times,
allow at least 10 minutes’ break for the camera flash.
In poorly-lit or low-contrast shooting environments, the built-in auto
focus assist beam will automatically light on to make it easier for
autofocus. The beam will light up only when autofocus is difficult
and get out as soon as the autofocus becomes correct.
Auto Focus Assist Beam
If you want to turn off the auto focus assist beam, set the “AF” to
“OFF” on the C.Fn settings.
X-PRO2, X-T20, X-T2, X-T1, GFX50S, GFX50R, X-T30
●
If you find the auto focus assist beam does not light up, this
is because the camera has got a correct autofocus.
●
Camera models that support auto focus assist beam:
Position
Center
Periphery
Effective Range
0.6~10m / 2.0~32.8 feet
0.6~5m / 2.0~16.4 feet
-
21
-
-
22
-
RX
2. Please make sure that whether the flash has finished its
recycle or caught up with the continuous shooting speed or
not(the flash ready indicator is lighten) and the flash is not
under the state of over-heat protection or other abnormal
situation.
→
Please turn on the “close distance wireless mode” on the flash
→
Please replace the battery(the flash trigger is recommended to
use 1.5V disposable alkaline battery).
1.
Disturbed by the
2.4GHz
signal in outer environment (e.g.
wireless base station,
2.4GHz
wifi router, Bluetooth, etc.)
→
T
o
adjust the channel CH setting on the flash trigger (add 10+
channels) and use the channel which is not disturbed. Or turn off
the other
2.4GHz
equipment in working.
→
Please downgrade the flash power output. If the flash is in TTL
mode, please try to change it to M mode(a preflash is needed in TTL
mode).
3. Whether the distance between the flash trigger and the flash
is too close or not
trigger (
＜
0.5m):
ST-III+
&
ST-III
series: press the test button and hold on, then
turning it on until the flash ready indicator blinks for 2 times.
ST-IV
series: Set the C.Fn-DIST to 0-30m.
4. Whether the flash trigger and the receiver end equipment are
in the low battery states or not
The Reason & Solution of Not Triggering in
PIXAPRO
2.4GHz
Wireless
9
.
TTL/M Shortcut Function
1. In non TTL wireless mode, push the TTL/M shortcut can
quickly change to flash mode.
2. When switching TTL to M manual mode, there is TCM switch
by default.
RX
10
.
Lock Function
In any interface, long press the MENU button for 2 seconds to
lock or unlock the operation function of interface. LOCKED will
be displayed when being locked.