background image

CurrentLeak

TM

Ground fault monitor

INTRODUCTION

This  manual  describes  how  to  install  this  Whole  Home  Ground  Fault  Monitor,
CurrentLeak

TM

  in  a  single  phase  service  entrance  combination  panel.  These

instructions  do  not  cover  all  details  or  variations  of  service  entrances,  if  you
require more information regarding a particular application that is not covered in

this manual, please contact a licensed/qualified electrical contractor.

WHEN INSTALLED ACCORDING TO THIS MANUAL,

 this product will provide

a  visual  display  of  the  ground  fault  level  in  your  entire  electrical  system.  This
product  will  not  prevent  ground  faults  from  occurring  or  prevent  electrical  fires
related  to  ground  faults.  In  order  to  prevent  electrical  fires  related  to  ground
faults,  it  is  the  sole  responsibility  of  the  end  user  to  ensure  their  electrical
system is and remains free of all ground faults at all times.

THIS PRODUCT WILL NOT 

monitor and display ground fault levels in electrical

systems  that  are  not  grounded  and/or  do  not  have  grounded  branch  circuits
and/or  is  not  installed  in  accordance  to  the  instructions  in  this  manual.  If  you
have  questions  or  require  assistance,  contact  a  licensed/qualified  electrical
contractor.

THIS  MANUAL  PROVIDES  PROCEDURES

  to  isolate  branch  circuits  that

contain  ground  faults,  a  licensed/qualified  electrician  shall  repair  all  ground
faults.

IMPORTANT !

THIS PRODUCT SHALL BE INSTALLED 

by a licensed/qualified  electrician in

accordance to the instructions in this manual, Canadian Electrical Code (CEC)
or  National  Electrical  Code  (NEC)  or  other  applicable  county  codes,  and  any
applicable  local  codes.  All  applicable  electrical  codes  supersede  these
instructions.

THIS INSTALLATION REQUIRES REMOVING AND  REPLACING

  the  factory

installed  neutral  bond  in  the  service  entrance  panel.  Some  jurisdictions  may
have  special  requirements to  permit  the  removal  and  replacement  of  a  factory
installed neutral bond.
If  you  have  questions  or  require  assistance,  contact  a  licensed/qualified
electrical contractor or the electrical authority in your jurisdiction.

WARNING! SHOCK HAZARDS

Improper  installation  and/or  wiring  can  cause  death,  injury  and/or
equipment damage.

Follow warnings and cautions. Completely read and understand the information
in  this  manual  before  attempting  to  install  or  operate  this  product.  Only
licensed/qualified  electricians  who are  trained  in  the  installation  and  service of
electrical devices shall install and/or service this equipment.

KEEP THESE INSTRUCTIONS FOR FUTURE USE

©

Pivotal Product Developments - All Rights Reserved

PARTS DESCRIPTION

CurrentLeak

TM

 monitor

Current transformer

Ethernet cable

9VDC power adaptor

Wire lugs X2

#6 AWG copper bonding cable

Mounting screws X4

Mounting wall anchors X4

SPECIFICATIONS

Patented

WHOLE HOME

INSTALLATION

INSTRUCTIONS

FOR ONTARIO, CANADA ONLY

WHOLE HOME MONITORING REQUIRES REMOVING AND REPLACING

 the factory installed neutral bond

in the service entrance panel which is permitted in Ontario, Canada, pursuant to the Electrical Safety Authority
(ESA) Bulletin - Ground Fault Monitoring (2-024, 2-034, 10-210, 10-614 Whole Home Ground Fault Monitoring).

Model number

MV1

CTV1

Description

CurrentLeak  monitor

Current transformer

Intended use

Indoor use, Max 400A service entrance panel

Operating conditions

5-40°C, 80% max RH at 5-31°C,
decreasing linearly to 50% max RH at 40°C

Altitude

Max 2,000m

Input supply voltage

120v, 60Hz

9vDC

Output Voltage

9VDC

N/A

Input current

0.132A

0-99mA

Max rated current

0.67A

70.995A

Dimensions  W x H x D (mm)

83.8 x 136.4 x 27.9

48 x 95.5 x 38.5

W x H x D (in)

3.3 x 5.37 x 1.1

1.89 x 3.76 x 1.52

Pivotal Product Developments Ltd.

244 Brockport Drive, Unit 12, Toronto, ON M9W 6X9

WARRANTY AND EXCLUSIONS

Pivotal  Product  Developments  Ltd  warrants  this  product  for  a  period  of  1  year  from  the  date  of  delivery  to  the  purchaser  to  be  free  from  defects  in  both  workmanship  and
material. Pivotal Product Developments Ltd assumes no risk or liability for the results of the use of the product purchased from it, including but without limiting the generality of

the foregoing: (1) The use in combination with any electrical or electronic components, circuits, systems, assemblies, or any other materials or substances; (2) Unsuitability of any

product for use in any circuit or assembly. Purchaser's rights under the warranty shall consist solely of requiring Pivotal Product Developments Ltd to repair, or at Pivotal Product
Developments  Ltd's  sole  discretion,  replace,  free  of  charge,  F.O.B  factory,  and  defective  items  received  at  said  factory  within  said  term  determined  by  Pivotal  Product
Developments Ltd to be defective. The giving of or failure to give any advice or recommendations by Pivotal Product Developments Ltd shall not constitute any warranty by or
impose any liability upon Pivotal Product Developments Ltd.

The  foregoing  constitutes  the sole and  exclusive liability  of Pivotal  Product Developments  Ltd  AND  IS  IN LIEU OF  ANY AND  ALL  OTHER  WARRANTIES  EXPRESSED,  IMPLIED OR
STATUTORY  AS  TO  THE  MERCHANTABILITY,  FITNESS  FOR  THE  PURPOSE  SOLD,  DESCRIPTION,  QUALITY,  PRODUCTIVENESS  OR  ANY  OTHER  MATTER.  In  no  event  shall  Pivotal

Product Developments  Ltd be  liable  for  special  or  consequential  damages  or for  delay  in  performance  of the  warranty.  This warranty  does  not  apply if  the  product has  been
misused, abused, altered, tampered with, or used in applications other than specified in the manual. At the end of the warranty period, Pivotal Product Developments Ltd shall be
under  no  further  warranty  obligation  expressed  or  implied.  The  product  covered  by  this  warranty  certificate  can  only  be  repaired  or  replaced  by  the  factory.  Repair  or
replacement units will be return collected. If Pivotal Product Developments Ltd finds the return to be a manufacturer's defect, the product will be return prepaid.

RETURN POLICY

The purchaser may return the product in it's original packaging, prepaid, within thirty (30) days of the original purchase date for a full refund of the purchase price, not including
freight or shipping charges that may have been paid by the purchaser as part of the original purchase. A copy of the original invoice must be included with the returned product.

Pivotal Product Developments will promptly issue a refund providing that the product is not damaged or in non re-sellable condition. Pivotal Product Developments is under no
obligation to provide a refund if it finds, at it's sole discretion, that the product is damaged or in non re-sellable condition.

Pivotal Product Developments Ltd.

Att: Quality Assurance Department, 

244 Brockport Drive, Unit 12 Toronto, Ontario M9W 6X

9

Отзывы: