3
OFF
OFF
ON
1
1
2
2
Bright
Dark
4
-cylinder
5
6
8
3
2
1
Special
A
3
Settings
Opening Demo
1
2
1
Tachometer display
Tachometer display
Tachometer display
Tachometer display
Tachometer display
Tachometer display
3
4
5
Real-time
Chronometric
Shift Lamp changes by pressing the switch.
3
Shift Lamp ON (Setting)
2
5
4
＋
1
Display Peak reading and reset the value.
1
5
2
3
4
3
2
4
1
5
While holding down the
switch, change the RPM setting
1
2
4
5
Opening Demo
Keep pressing the switch
The ignition OFF
(Meter light Off)
3
2
5
6
4
While holding down the switch,
change the brightness setting.
Switching the Chronometric / Real-time Display.
SETTING
B
Switching the Display
(Chronometric/ Real-time)
Pressing the switch changes
the display mode.
While the tac hometer is being
displayed, press the switch once.
Shift Lamp ON
Each pressing will decrease the brightness;
when pressed at the darkest setting it will
return to the brightest possible setting.
5 steps
SETTING
A
Cylinder Number Setting
SETTING
E
Shift lamp brightness setting
Press for 3 seconds
Make setting to change the shift lamp brightness.
(It will be the minimum brightness if Orange cable is wired to parking light.)
With no operation
for 5 seconds
Reference: If the engine is a two cycle engine, multiply the number of cylinder by two.
(e.g., For a two-cycle three-cylinder engine the setting would be six.)
Set the cylinder number for the car being used.
The number of cylinders is set by the shift lamp pattern.
Press the
switch once
With no operation
for 5 seconds
Press the switch
for 3 seconds
Press the
switch
With no operation
for 5 seconds
Press the switch
for 5 seconds
SETTING
F
Switching the signal level
Press for 5 seconds
6
7
After finishing the installation, make various settings.
(The factory default setting is for a
four-cylinder engine)
Cylinder
display
Turn
1
2
3
4
5
6
8
Special
A
Number of
cylinders
NISSAN (FAIRLADY Z Z33) / MAZDA (ATENZA and others)
MAZDA (RX-8) / SUBARU (early type of PLEO and others)
Three-cylinder
Four-cylinder and Rotary engine (RX-7)
Five-cylinder
Six-cylinder
Eight-cylinder
Some models of NISSAN
Car models
Shift lamp
Patterns for cylinder settings display
= On
= Off
= Blink
The lamps blink red
Changes are only necessary for those car models listed below.
NISSAN (FAIRLADY Z Z33)/ MAZDA (after 2002)/ MITSUBISHI (COLT and others)
/
SUBARU (early type of PLEO and others)
⇒
See the “Wiring Chart” for details.
All shift lamps will light
Press the
switch once
SETTING
C
Peak reading display and re-set
Peak reading
display
Peak reading
display
Press
Press
Press the switch
for 2 seconds
Pressing the switch will re-set the
peak reading.
The needle will show “0”
The needle will show “0”
All shift lamps will light
1
= If the generic car
2
= If the level is small
Press the
switch
Press the
switch
While holding the switch, start
the engine within 5 seconds.
ENGINE
START
SETTING
D
Shift Point Setting
Press for 1.5 seconds
With no operation
for 5 seconds
Press the switch
for 1.5 seconds
Press the
switch
Each pressing of the switch will
raise, the set ting 20 0 r pm; at
peak it will return to 3000 rpm.
The lamps blink red
The needle will show the
set shift point
Make RPM setting for turning on the shift lamp. (Setting Range: 3000–9000rpm)
Preparation
Please check the number of cylinders and cycles for the model car being used.
With no operation
for 5 seconds
Press the
switch once
Press the switch to change the
pattern and set to the proper one.
W h i l e t h e t a c h o m e t e r i s b e i n g
displayed, press the switch for long.
W h i l e t h e t a c h o m e t e r i s b e i n g
displayed, press the switch for long.
Set the signal detection level
by p r e s s i n g t h e s w i t c h t o
change the needle position
to the correct setting.
While the tachometer is being
displayed, press the switch once.
Note: By continually pressing down on
the switch the needle will move to peak.
Af ter 1. 5 seconds the shif t
point will be shown and after
3 seconds all lamps will light
Press the
switch
The needle will show “1” or “2”
Press the switch with the ignition in
the OFF position (meter light off).
Press the
switch
⇒
See
SETTING F
for details.
Note 1:
For one and two cylinder engines,
set the signal level switch to two.
Press the switch with the
ignition in the OFF position
(meter light off)
Turn the ignition to
the ON position
(engine not running)
