(+)
(—)
(+)
(—)
(+)
(—)
LEFT STROBE
POWER SUPPLY
(+)
(—)
(+)
(—)
(+)
(—)
RIGHT STROBE
POWER SUPPLY
TO NEXT
DEVICE
OR EOL
TO NEXT
DEVICE
OR EOL
D600-01-00
2
I56-1569-002R
The strobe will not work without power.
The strobe gets its power from
the fire/security panel monitoring the alarm system. If power is cut off for
any reason, the strobe will not provide the desired visual warning.
NOTE: Strobes must be powered continuously for horn operation.
The signal strobe may not be seen.
The electronic visual warning signal
uses an extremely reliable xenon flash tube. It flashes at least once every
second. The strobe must not be installed in direct sunlight or areas of high
light intensity (over 60 foot candles) where the visual flash might be dis-
regarded or not seen. The strobe may not be seen by the visually impaired.
The signal strobe may cause seizures.
Individuals who have positive
photic response to visual stimuli with seizures, such as persons with
epilepsy, should avoid prolonged exposure to environments in which
strobe signals, including this strobe, are activated.
The signal strobe cannot operate from coded power supplies.
Coded
power supplies produce interrupted power. The strobe must have an unin-
terrupted source of power in order to operate correctly. System Sensor rec-
ommends that the horn and signal strobe always be used in combination
so that the risks from any of the above limitations are minimized.
The Limitations of Strobes
WARNING
Figure 2. Powered by a 4-wire circuit to provide independent left
strobe and right strobe operation (Remove factory installed
jumpers, see Figure 1B):
NOTE: Strobes must be powered continuously for proper operation.
Figure 3: Synchronizing strobes using MDL:
Three-Year Limited Warranty
System Sensor warrants its enclosed strobe or strobe to be free from
defects in materials and workmanship under normal use and service for a
period of three years from date of manufacture. System Sensor makes no
other express warranty for this strobe. No agent, representative, dealer, or
employee of the Company has the authority to increase or alter the obli-
gations or limitations of this Warranty. The Company’s obligation of this
Warranty shall be limited to the repair or replacement of any part of the
strobe which is found to be defective in materials or workmanship under
normal use and service during the three year period commencing with the
date of manufacture. After phoning System Sensor’s toll free number 800-
SENSOR2 (736-7672) for a Return Authorization number, send defective
units postage prepaid to: System Sensor, Repair Department, RA
#__________, 3825 Ohio Avenue, St. Charles, IL 60174. Please include a
note describing the malfunction and suspected cause of failure. The
Company shall not be obligated to repair or replace units which are found
to be defective because of damage, unreasonable use, modifications, or
alterations occurring after the date of manufacture. In no case shall the
Company be liable for any consequential or incidental damages for breach
of this or any other Warranty, expressed or implied whatsoever, even if the
loss or damage is caused by the Company’s negligence or fault. Some
states do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitation or exclusion may not apply to
you. This Warranty gives you specific legal rights, and you may also have
other rights which vary from state to state.
Mounting
If you would prefer to switch the lens colors, the strobe modules are field-
reversible. (Fig. 4)
To reverse the strobe module: insert screwdriver, as shown in Fig. 4, to
unlock snap. While pushing in the screwdriver, pull back on the strobe
module. Hinge the strobe module, disengage the Locking Rib, and lift the
module away from the mounting plate. Turn the module so that it is
upside down from its original position, re-insert the module into the
mounting plate (be sure to insert the Locking Rib into the slot), and press
the module into the mounting plate. The strobe module will make a
“click” when it has locked into place. Turn entire assembly so that the
lenses are on the bottom. The unit can now be mounted.
The unit can be mounted to a single-gang back box, or to a 4
″
x 4
″
back
box, using the mud ring provided.
1. Complete field wiring.
2. Align dual strobe over back box
and secure with screws.
2-INCH BACK BOX
#6-32
PAN HEAD
SCREWS
INSERT SCREWDRIVER
INSERT SCREWDRIVER
POWER
SUPPLY
MDL
RED
STROBES
POWER
SUPPLY
MDL
AMBER
STROBES
TO NEXT
DEVICE
OR EOL
TO NEXT
DEVICE
OR EOL
Please refer to insert for the Limitations of Fire Alarm Systems
INSERT SCREWDRIVER
INSERT SCREWDRIVER
LOCKING RIB
INSERT SCREWDRIVER
TO REMOVE
Figure 4: Reversing the strobe module:
