PITSOS GVC762ST, Руководство пользователя, Страница: 19 / 25

19
3 Slide the new SAFBAG tab all the way into the holder
guide as directed by the arrow printed on the bag until tab
locks in the guide.
4
Put the SAFBAG holder (22) in the container and cover with
the filtration unit in accordance with paragraphs C2 and C3 .
If the SAFBAG dust bag is not properly attached
to the holder, the safety lock will prevent
covering the container with the filtration unit.
VACUUM CLEANING WITH THE USE OF THE
WATER FILTER MODULE
1
Press and hold the container lid opening button (2) and
lift the container lid.
2 Insert the partition in the container. Make sure the
partition is inserted correctly in the container guide slots and
the safety lock is engaged.
3 Fill the container with 1,3–1,5 liter of water. The water
level should be in the range marked on the wall of the
container.
Do not operate the appliance with an empty
container while vacuum cleaning with the use
of the water filter module.
4 Cover the container with the filtration unit.
If the partition is not inserted properly, the
safety lock will prevent covering the container
with the filtration unit.
●
Prepare the vacuum cleaner for operation according
to section B.
●
The vacuum cleaner starts at the same power level
it had been working before it was turned off. Set the
desired power value by pressing the power adjustment
b/- (9) .
Do not operate the appliance for too long
without replacing the water in the container.
WET VACUUMING AND WET CLEANING
Before using the wet cleaning function thoroughly vacuum
the surface to be cleaned.
Before operating the vacuum cleaner make sure the container
is empty and the water filter module and the filters are clean.
1 Press and hold the container lid opening button (2) and
lift the container lid.
2 Remove the container together with the water filter
module (filtration unit and partition) from the vacuum cleaner.
3 Remove the cleaning liquid container (24) by pulling it by
the handle and lifting it upwards.
4
Open the filler cap and fill the cleaning liquid container
(24) with cleaning agent (a mixture of cleaning fluid G 500
O Tens (30) and cold water). Use the amounts stated on the
fluid bottle label:
–
“G 500 O Tens” manufactured by BUZIL, Germany.
E
F
●
Close the filler hole of cleaning liquid container with the
cap.
Before wet cleaning the carpet, check the colour
fasteness of cleaned carpet. Put a small amount
of prepared solution on white cloth and clean
manually the carpet at least visible place. If the
cloth is dyed, it means that the carpet colours
are not permanent and the carpet cannot be
cleaned using cleaning fluid G 500 O Tens.
5 Insert the cleaning liquid container (24) back to the
previous position and press the container to fix it correctly
(proceed in the reverse order as in case of removing the
container).
6 Insert the container together with the water filter module
(filtration unit and partition) to the vacuum cleaner.
For protection against the formation of foam or at its
formation, when cleaning fill the rear container with an
anti-foaming agent (30) recommended by the company
PITSOS, in the amounts specified on the label:
–
“G 478 Buz
®
Defoam” manufactured by company BUZIL,
Germany.
●
Prepare the vacuum cleaner for operation according
to section B.
Use only the large or small atomizing nozzle for
wet vacuum cleaning.
●
The vacuum cleaner starts at the same power level
it had been working before it was turned off. Set the
desired power value by pressing the power adjustment
b/- (9) .
7 Press the pump switch (7) .
The pump may only be switched on when
the cleaning liquid container is filled with the
solution of cleaning liquid and water. The lack
of cleaning liquid manifests in a loud operation
of the pump.
If the nozzle does not atomize water although the pump is
switched on, check if the following items are correctly installed:
the cleaning liquid container (press the container), the fastening
of the stub pipe in the valve in the base of the vacuum cleaner
or the fastening of the hose end in the atomizing nozzle, check
if the atomizing nozzle is not clogged.
8
Press the button adjusting the inflow of water to the
nozzle on the hose handle.
If you press the button in a pulsating manner, the water shall
temporarily flow in a slower manner to the nozzle, if you
press and slide the button backwards, the water shall be
continuously supplied to the nozzle.
The handle is also equipped with a slider to adjust the suction
power. Do not uncover this opening while picking up water or
using the wet cleaning function.
Do not spray the cleaning liquid in one place
on the carpet for too long in order not to soak
the carpet.