12
GVC225SP-001PI_v01
(De)installing the SAFBAG-type bag
C
Vacuum cleaner is equipped with SAFBAG bag (1 piece).
The vacuum cleaner is equipped with safety
valve located in chamber of dust container
(bag). It opens automatically in case of total
stopping of suction hose or total stopping of
equipment elements connected thereto, as well
as in case of overfill of dust bag. After opening
the valve one can hear characteristic “whirr”
sound inside the vacuum cleaner.
1
The vacuum cleaner is equipped with a full bag indicator
(5)
. When the indicator light is on during work (a nozzle or
brush is over a cleaned surface), it means the bag needs to be
replaced. The full bag indicator
(5)
may also be on when the
suction hose or other accessories linked to it are clogged up.
2
Press the on/off switch
(4)
to stop the vacuum cleaner.
Remove the plug of the cord from the socket.
3
Press both of the side buttons situated on the end of the
hose, and remove the end of the hose from the inlet of the
vacuum cleaner.
4
Release the fastening of the upper cover (
6)
, and open it.
5
Close the opening of the bag by means of a stopper.
6
Bend back the bag handle in the direction of the vacuum
cleaner handle
(7)
.
7
Grab the bag plate, pull it out of the handle, and then
remove the entire bag upwards.
8
Place the bag plate of a new bag into the guides of the
SAFBAG handle, and slide it to the limit.
9
Bend back the bag handle in the direction of the control
knob
(4)
.
10
Close the cover by pressing it, until you hear
a characteristic “click” – be careful not to trap the bag.
Do not start vacuuming without the SAFBAG-
type bag. No SAFBAG-type bag makes it
impossible to lock the upper cover of the
vacuum cleaner.
You have to replace the bag, if:
a) the full bag indicator is on,
b) the vacuum cleaner works less efficiently,
c) the bag is full.
(De)installing the EPA inlet filter and the
foam rubber
Before replacing the EPA inlet filter and the foam rubber,
make sure the vacuum cleaner is turned off, and the plug of
the cord is out of the electrical socket.
INTAKE FILTER (EPA)
The vacuum cleaners are equipped with a EPA E11-class
inlet filter.
1
Release the fastening of the upper cover
(6)
, and open it.
D
2
Remove the SAFBAG-type bag
(13)
from the chamber of
the vacuum cleaner.
3
Pull out the EPA intake
(11)
from the guides situated at
the back wall of the chamber of the vacuum cleaner.
4
Put the new filter into the guides situated at the back wall
of the chamber of the vacuum cleaner.
Always replace a damaged EPA intake filter (11)
with a brand new, original one. The EPA intake
filter is guaranteed to make the vacuum cleaner
to work efficiently for ca. a year.
5
Place the SAFBAG-type bag into the chamber of the
vacuum cleaner.
6
Close the cover by pressing it, until you hear
a characteristic “click”.
FOAM RUBBER COVER
1
Release the fastening of the upper cover
(6)
, and open it.
2
Remove the foam rubber cover
(12)
from the three
fastenings of the upper cover.
3
Replace the old foam rubber cover with a new one
(12)
in such a way that the three incisions on the foam rubber
cover find the three fastenings of the upper cover.
Always replace a damaged foam rubber cover
(12) with a brand new, original one.
4
Close the cover by pressing it, until you hear
a characteristic “click.”
After-work procedures, cleaning and
maintenance
1
Press the on/off switch
(4)
to stop the vacuum cleaner.
2
Remove the plug of the cord from the socket.
3
Wind the cord by pressing the cord winder button
(3)
.
Hold the cord when doing it to avoid tangling the cord up or
letting the plug hit the vacuum cleaner.
4
Disconnect the telescopic pipe from the nozzle or brush.
5
Disconnect the telescopic tube from the hose. In order to
remove the tube from the hose handle press the
“A”
locking
device and pull the tube in the direction of the arrow.
6
Press both of the side buttons situated on the end of the
hose, and remove the end of the hose from the inlet of the
vacuum cleaner.
7
The vacuum cleaner together with its attached accessories
may be stored in a vertical or horizontal position. In order to
this, place the hook of the nozzle brush into the fastening for
the nozzle brush. The hose may stay attached to the vacuum
cleaner as long as it is not bent too much during storage.
8
If necessary, clean the casing and the chamber of the
vacuum cleaner with a damp cloth (it may be damped in
dishwashing liquid), dry it off, and wipe it dry.
Do not use any scrubbing agents or solvents.
E
F