Pitney Bowes Relay 2500 Скачать руководство пользователя страница 131

Страница: 131 / 182

Clearing Material Jams in the Sheet Feeder

Remove the sheet feeder trays

- lift the rear of the tray slightly and pull it straight out from the

inserter.

If the tray is loaded, gently hold the material in place to prevent it sliding forward as the tray is
removed.

2. Remove the jammed material. If necessary,

use the manual advance knob

to move the material

forward.

NOTE

: Avoid pulling pages backwards out of the machine, towards the sheet feeder. It is better

to clear sheet feeder jams by moving material forward and removing it from the accumulator
area.

Replace the sheet feeder trays

a. Place the tray into its location guides in the side frames.

b. Lift the rear of the tray slightly and push it into the inserter. The tray automatically drops into its

correct position.

Error Recovery and Clearing Material Jams

Pitney Bowes

Relay™ 2500, 3500, 4500 User Guide

December, 2018

Page 124 of 174

Содержание Relay 2500






















































































































































































Результаты поиска

Содержание Relay 2500

Отзывы:

Похожие инструкции для Relay 2500

Бренды по названию

Популярные бренды

Pitney Bowes Relay 2500, Руководство пользователя

Результаты поиска

Содержание Relay 2500

Отзывы:

Похожие инструкции для Relay 2500

Бренды по названию

Популярные бренды