Pit Boss 72750 Скачать руководство пользователя страница 7

Страница: 7 / 32

ASSEMBLY PREPARATION

Parts are located throughout the shipping carton, including underneath the grill. Inspect the grill, parts, and hardware blister

pack after removing from the protective shipping carton. Before assembly of product, review all parts and reference the parts

list. If any part is missing or damaged, do not attempt to assemble. Shipping damage is not covered under warranty. Contact your

dealer or Pit Boss Customer Service for parts.

IMPORTANT: To ease installation, using two people is helpful (but not necessary) when assembling this unit.

Tools required for assembly:

screwdriver, wrench and level.

Tools not included.

ASSEMBLY INSTRUCTIONS

IMPORTANT: It is advised to read each step entirely before starting assembly on instructions. Do not tighten screws

completely until all screws for that step have been installed. Hardware combination involving a locking washer and

washer should be installed with the locking washer closest to the head of the screw.

1. MOUNTING THE LEGS TO THE MAIN BARREL

Parts Required:

1 x Main Barrel

(#6)

2 x Stationary Leg

(#9)

2 x Leg with Wheel

(#110

16 x Screw

(#A)

16 x Locking Washer

(#C)

16 x Washer

(#B)

Installation:

• Place a piece of cardboard on the floor to prevent scratching the unit.
• Open the main grill lid and remove the four screws in the center of

the large diffuser plate. Remove from main barrel and set aside. These

parts will be re-installed on a later step. Note illustration 1A.

• Next, lay the main barrel on its side, hopper end pointed upward, on the

cardboard. Mount one leg with wheel axle to the floor end of the main

barrel using four screws, locking washers, and washers, through the four

pre-drilled holes. Repeat installation for second leg with wheel axle.

• Mount one stationary leg to the hopper end of the main barrel using

four screws, locking washers, and washers, through the four pre-drilled

holes. Repeat installation for second stationary leg. Note illustration 1B.

Содержание 72750

































Результаты поиска

Содержание 72750

Отзывы:

Похожие инструкции для 72750

Бренды по названию

Популярные бренды

Pit Boss 72750, Инструкция по сборке и эксплуатации

Результаты поиска

Содержание 72750

Отзывы:

Похожие инструкции для 72750

Бренды по названию

Популярные бренды