Pit Boss 10719, Руководство по сборке и эксплуатации

Страница: 36 / 88

FRANÇAIS
36
2. FIXER CORRECTEMENT LE PANNEAU DE COMMANDE AUX
PIEDS DE SUPPORT AVANT
Pièces nécessaires :
2 x Vis (#C)
Installation :
• Près du panneau de commande, desserrez les deux vis reliant le
panneau avant à l'armoire principale.
• À l'aide de deux autres vis, fixez les côtés du panneau avant aux pieds
de support orientés vers l'avant. Une fois ces vis serrées, resserrez les
deux vis précédemment desserrées.
3. FIXATION DE LA BARRE D'APPUI
Pièces nécessaires :
1 x Barre d'appui (#15)
4 x Vis (#C)
Installation :
• Installez le support à l'arrière de l'unité entre les deux pieds de support
arrière. Fixez en utilisant deux vis de chaque côté. Assurez-vous que le
support est placé sur le dessous de l'armoire principale, vers l'intérieur.
Regardez l'illustration pour assembler les supports.
4. MONTAGE DES PANNEAUX DE SUPPORT
Pièces nécessaires :
2 x Panneaux de support (#20)
8 x Vis (#C)
Installation :
• Installez un panneau de support sur le côté de l'unité entre un pied
de support avant et un arrière. Fixez en utilisant deux vis de chaque
côté. Assurez-vous que le côté plat de la plaque de support est orienté
vers l'extérieur. Répétez le même processus pour assembler les autres
panneaux de support. Regardez l'illustration pour assembler les
panneaux de support.
7
2. MOUNTING BOTH FRONT LEGS TO
LOWER CABINET WITH CONTROL
PANEL ASSEMBLY
Parts Required:
1 x Lower Smoker Cabinet with
1 x Right Front Leg (#22)
1 x Left Front Leg (#21)
2 x #10-24*1/2”Screw (#C)
Installation:
rews which were
pre-assembled on the Control to
Cabinet mount Right Front Leg (#22)
Assembly (#14) using 2 x #10-24*1/2”Screws
(#C) and re-tighten 2 screws on the Control
Fig.2.1 shown.
3. MOUNTING BACK SUPPORT TUBE TO
RIGHT REAR LEG WITH WHEEL
ASSEMBLY AND LEFT REAR LEG WITH
WHEEL ASSEMBLY
Parts Required:
1 x Back Support Tube (#23)
1 x Right Rear Leg with Wheel Assembly (#18)
1 x Left Rear Leg with Wheel Assembly (#20)
4 x #10-24*1/2”Screw (#C)
Installation:
• Mount Back Support Tube (#23) to the Right
Rear Leg with Wheel Assembly (#18) and Left
Rear Leg with Wheel Assembly (#20)using 4 x
#10-24*1/2”Screws (#C)as Fig.3 shown.
3
Installation:
Front Leg (#22)
#10-24*1/2”Screws (#C) as Fig.4 shown.
Leg (#21)
Assembly (#20) using 4 x
#10-24*1/2”Screws (#C) as Fig.4 shown.
5. MOUNTING BURNER CHAMBER
ASSEMBLY TO THE BOTTOM AREA OF
LOWER SMOKER CABINET ASSEMBLY
Parts Required:
1 x Burner Chamber Assembly (#24)
1 x Lower Smoker Cabinet with Control
Panel Assembly (#14)
4 x #10-24*1/2”Screw (#C)
Installation:
• Attach ignition wire onto the pin end of
the Igniter on Control Panel.
Mount Burner Chamber Assembly (#24) to
the bottom area of Lower Smoker Cabinet
with Control Panel Assembly (#14) using 4
x #10-24*1/2”Screws (#C) as Fig.5.1 &
Fig.5.2 shown.
Note: MUST make sure
that the tip of the valves
are completely INSIDE
the end opening of the
Burner Tubes.
Note: Turn the Lower Smoker Cabinet with
Control Panel and Legs Assembly Right
Side Up as Fig.5.3 shown and tighten all
screws now.
4
15
20
20
7
2. MOUNTING BOTH FRONT LEGS TO
LOWER CABINET WITH CONTROL
PANEL ASSEMBLY
Parts Required:
1 x Lower Smoker Cabinet with
1 x Right Front Leg (#22)
1 x Left Front Leg (#21)
2 x #10-24*1/2”Screw (#C)
Installation:
rews which were
pre-assembled on the Control to
Cabinet mount Right Front Leg (#22)
Assembly (#14) using 2 x #10-24*1/2”Screws
(#C) and re-tighten 2 screws on the Control
Fig.2.1 shown.
3. MOUNTING BACK SUPPORT TUBE TO
RIGHT REAR LEG WITH WHEEL
ASSEMBLY AND LEFT REAR LEG WITH
WHEEL ASSEMBLY
Parts Required:
1 x Back Support Tube (#23)
1 x Right Rear Leg with Wheel Assembly (#18)
1 x Left Rear Leg with Wheel Assembly (#20)
4 x #10-24*1/2”Screw (#C)
Installation:
• Mount Back Support Tube (#23) to the Right
Rear Leg with Wheel Assembly (#18) and Left
Rear Leg with Wheel Assembly (#20)using 4 x
#10-24*1/2”Screws (#C)as Fig.3 shown.
2
7
2.
MOUNTING BOTH FRONT LEGS TO
LOWER CABINET WITH CONTROL
PANEL ASSEMBLY
Parts
Required:
1 x Lower Smoker Cabinet with
1 x Right Front Leg (#22
)
1 x Left Front Leg (#21
)
2 x #10-24*1/2”S
crew (#C
)
Insta
llation
:
rew
s whi
ch were
pre-a
ssembled
on
the
Con
trol
to
Cabine
t
moun
t Righ
t Fron
t Leg
(#22)
Ass
embl
y (#14)
using
2 x
#10-24*1
/2”Sc
rews
(#C)
and
re-
tigh
ten
2 s
crew
s on
the
Con
trol
Fig.2
.1 shown.
3.
MOUNTING BACK
SUPPORT TUBE
TO
RIGHT REAR
LEG WITH WHEEL
ASSEMBLY
AND
LEFT REAR
LEG WITH
WHEEL ASSEMBLY
Parts
Required:
1 x Back Support Tube (#23)
1 x Right Rear Leg
with Wheel Assembly (#18)
1 x Left Rear Leg with Wheel Assembly (#20)
4 x #10-24*1/2”Screw (#C)
Insta
llation
:
• Mount Back Support Tube (#23) to the Right
Rear Leg with Wheel Assembly (#18) and Left
Rear Leg with Wheel Assembly (#20)using 4 x
#10-24*1/2”Screws (#C)as Fig.3 shown.