manualshive.com logo in svg

Piscine Solide V35023, Руководство по установке

Поделиться
Скачать
Piscine Solide V35023 Скачать руководство пользователя страница 41

POOL MAINTENANCE

WINTERIZING YOUR POOL

Section

5

No Diving or Jumping.  Observe all Safety Rules

5-3

Section

5

CLOSING YOUR ABOVE GROUND POOL FOR THE WINTER

At the end of the season, you must follow these directions to make your pool ready for the winter. For areas where 
water freezes make sure to follow these instructions before the water is frozen, otherwise do not touch the frozen 
water, this may damage the pool.

STEP 1)  

PRIOR TO CLOSING

a.  Several days prior to closing your pool, test the water for the ph level, total alkalinity, and chloring. The water 

balance is important to protect the pool from corrosion or scale build-up during winter shut down. 

STEP 2)  

PERFORM A COMPLETE INSPECTION

FINDING LEAKS

a.    Towards the end of the summer season or around mid-August, check for leaks by verifying if the pool’s water 

level is stable. Draw a line on the liner marking the water level and wait 10 days. If after 10 days the level has 
dropped, then there is a leak. It is important to seal off any leaks you find. Leaks left unsealed when freezing 
begins can seriously damage your pool and even cause it to collapse. 

b.    Vacuum carefully to remove all leaves and debris.

CHECK THE LINER

a.    Make sure the top of the liner is still attached to the pool wall. make sure there are no leaks. Repair any liner 

holes with a vinyl patch: any small punctures in the liner can be easily repaired with underwater repair kits 
available at your local retailer. Do not remove the liner from the pool, as removal of the liner will void the 
existing warranty.

CHECK ALL JOINTS AND SCREWS

a.  Make sure all the fram joints are fitting together properly and make sure the pool wall has not shifted from 

the bottom rail. Ensure all screws and bolts are tight.

CHECK FOR RUST

a.  Periodically inspect the metal parts for any corrosion especially around the skimmer area. If corrosion is found, 

immediate corrective action must be taken. Wire brush any rust and add a coat of enamel primer followed by 
a coat of color matching anti-rust enamel paint. Pool structure failure could result in ma jor property damage 
and bodily harm. Paint any scratches with anti-rust paint.

Содержание V35023














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды