Piscine Solide REFLEXION V35013 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 42

background image

POOL MAINTENANCE

WINTERIZING YOUR POOL

No Diving or Jumping. Observe all Safety Rules

5-3

Section

5

WINTERIZING INSTRUCTIONS

For areas where water freezes make sure to follow these instructions before the water is frozen,
otherwise do not touch the frozen water, this may damage the pool.

a. Towards the end of the summer season or around mid-August, check for leaks by

verifying if the pool’s water level is stable. Draw a line on the liner marking
the water level and wait 10 days. If after 10 days the level has dropped,
then there is a leak. It is important to seal off any leaks you find. Leaks
left unsealed when freezing begins can seriously damage your
pool and even cause it to collapse.

b. Vacuum carefully to remove all leaves and debris.

c. Lower the water level so as to leave between 5 to 20 inches

(12.5cm to 50cm) below the water return. Depending on
your area and if the freezing point is more aggressive,
for example 50% is frozen into ice, we strongly suggest
to lowering the water to lowest point. Depending on
how great the deep freeze in your area

we suggest

you consult with your local dealer about procedures
on lowering the water level throughout the winter.

We also suggest throughout the autumn season
to continually check this level before freezing
season starts, as it must not reach the skimmer
holes at any time during the winter. Remove any
snow which may accumulate on the top ledge.

d. For the winter cover we suggest to lower the water

level to 1 inch (2.5cm) below the water return. In
some areas your dealer may ask you to install it
differently in order to protect the pool and the
cover. Contact your local dealer to verify the
correct procedure for your pool.

e. Remove and store the filter, ladder and all other

removable parts from around the pool. The
filter should be clear of any foreign objects and
water should be removed from the filter and pump.
See the manufacturer’s instructions. Store the pump
in a temperature controlled environment (so that it
is not damaged by changes in temperature).

Important Note:

An unsealed leak may comprise or cancel the guarantee on your pool.
Never leave water in any of the filtration system components due to the risk of damage
during freezing.

«
...
37
38
39
40
41
...
»

Содержание REFLEXION V35013











































Отзывы:

Нет отзывов

Похожие инструкции для REFLEXION V35013

Бренд: Zodiac Страницы: 12

MultiSystem MP 3500

Бренд: Messner Страницы: 10

Бренд: C.P.A. Страницы: 38

Deluxe Maintenance Kit

Бренд: Intex Страницы: 18

Бренд: Spectravision Страницы: 4

Бренд: UTC Страницы: 13

Бренд: Pahlen Страницы: 6

Бренд: Hydro-Pro Страницы: 230

VS FloPro Series

Бренд: Jandy Страницы: 84

Бренд: ccei Страницы: 24

Бренд: Raypak Страницы: 8

andy AquaPure EI Series

Бренд: Zodiac Pool Systems Страницы: 36

Бренд: Badu Tec Страницы: 36

Бренд: Dimplex Страницы: 5

Deluxe Thru-Wall Skimmer 1-4113-006

Бренд: Lomart Страницы: 8

Бренд: JJ Страницы: 103

Бренд: Intex Страницы: 7

Бренд: Intex Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды