The System Setup and Other Setup menus
11
80
En
•
Surr
– Select
LARGE
if your surround speakers
reproduce bass frequencies effectively. Select
SMALL
to send bass frequencies to the other
speakers or subwoofer. If you didn’t connect
surround speakers choose
NO
(the sound of the
surround channels is sent to the front speakers or a
subwoofer).
•
SB
– Select the number of surround back speakers
you have (one, two or none).
1
Select
LARGEx2
or
LARGEx1
if your surround back speakers reproduce
bass frequencies effectively. Select
SMALLx2
or
SMALLx1
to send bass frequencies to the other
speakers or subwoofer. If you didn’t connect
surround back speakers choose
NO
.
•
SW
– LFE signals and bass frequencies of channels
set to
SMALL
are output from the subwoofer when
YES
is selected. Choose the
PLUS
setting if you want
the subwoofer to output bass sound continuously or
you want deeper bass (the bass frequencies that
would normally come out the front and center
speakers are also routed to the subwoofer).
2
If you did
not connect a subwoofer choose
NO
(the bass
frequencies are output from other speakers).
3
Select ‘X. OVER’ and set the crossover frequency.
3
Frequencies below this point will be sent to the
subwoofer (or
LARGE
speakers).
4
When you’re finished, press RETURN.
You will return to the
Manual SP Setup
menu.
Channel Level
Using the channel level settings, you can adjust the
overall balance of your speaker system, an important
factor when setting up a home theater system.
1
Select ‘Channel Level’ from the Manual SP Setup
menu.
The test tones will start.
2
Adjust the level of each channel using
/
.
Use
/
to switch speakers.
Adjust the level of each speaker as the test tone is
emitted.
4
3
When you’re finished, press RETURN.
You will return to the
Manual SP Setup
menu.
Tip
• You can change the channel levels by press
, then press
CH LEVEL
, and then using
/
on the remote control.
Speaker Distance
For good sound depth and separation from your system,
you need to specify the distance of your speakers from
the listening position. The receiver can then add the
proper delay needed for effective surround sound.
1
Select ‘Speaker Distance’ from the Manual SP
Setup menu.
2
Adjust the distance of each speaker using
/
.
You can adjust the distance of each speaker in
1
/
2
inch
Increments.
3
When you’re finished, press RETURN.
You will return to the
Manual SP Setup
menu.
Tip
• For best surround sound, make sure the surround
back speakers are the same distance from the
listening position.
Note
1 • If you selected
ZONE 2
or
Front Bi-Amp
(in
Speaker system setting
on page 79) you can’t adjust the surround back settings.
• If the surround speakers are set to
NO
, the surround back speakers will automatically be set to
NO
.
2 If you have a subwoofer and like lots of bass, it may seem logical to select
LARGE
for your front speakers and
PLUS
for the subwoofer. This
may not, however, yield the best bass results. Depending on the speaker placement of your room you may actually experience a decrease in
the amount of bass due low frequency cancellations. In this case, try changing the position or direction of speakers. If you can’t get good
results, listen to the bass response with it set to
PLUS
and
YES
or the front speakers set to
LARGE
and
SMALL
alternatively and let your ears
judge which sounds best. If you’re having problems, the easiest option is to route all the bass sounds to the subwoofer by selecting
SMALL
for the front speakers.
3 • This setting decides the cutoff between bass sounds playing back from the speakers selected as
LARGE
, or the subwoofer, and bass sounds
playing back from those selected as
SMALL
. It also decides where the cutoff will be for bass sounds in the LFE channel.
• With Full Auto MCACC Setup or Auto MCACC Setup (
ALL
or
Speaker Setting
), the setting here will not apply and the crossover frequency
will be automatically set. Crossover frequency is a frequency aimed at achieving the optimal sound field taking into account the bass capacity
of all connected speakers and human aural characteristics.
• If you’re using THX speakers, confirm that the crossover frequency is set to
80Hz
.
4 If you are using a Sound Pressure Level (SPL) meter, take the readings from your main listening position and adjust the level of each speaker
to 75 dB SPL (C-weighting/slow reading).
RECEIVER
11he_System_setup.fm 80 ページ ２０１０年８月２４日 火曜日 午後３時２１分
Содержание VSX-1120-K
Страница 104: ...Additional information 12 104 En VSX 1120_UXJCB book 104 ページ ２０１０年３月１０日 水曜日 午後２時２分 ...
Страница 105: ...Additional information 12 105 En VSX 1120_UXJCB book 105 ページ ２０１０年３月１０日 水曜日 午後２時２分 ...
Страница 106: ...Additional information 12 106 En VSX 1120_UXJCB book 106 ページ ２０１０年３月１０日 水曜日 午後２時２分 ...
