background image

+

+

+

Fig. 3

7

When using a Subwoofer without using a different amp (sold separately)

This product

Antenna jack

Yellow
To terminal always supplied
with power regardless of
ignition switch position. 

Red
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.

Fuse holder

Black (ground)
To vehicle (metal) body.

Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.

Blue/white
To Auto-antenna relay control terminal 
(max. 300 mA 12 V DC).

IP-Bus input (Blue)

Multi-CD player
(sold separately)

Subwoofer output 

IP-BUS cable

Orange
To lightnig switch terminal.

Front speaker

Left

Front speaker

Subwoofer

Right

Front output

Gray

White

Gray/black

White/black

Violet

Green

Violet/black

Green/black

Do not connect anything to these speaker leads.

Note:
Change the Initial Setting of this product.
(Refer to the Owner’s Manual.)

Connecting the Units

<ENGLISH>

Installation

<ENGLISH>

Note:
• Before finally installing the unit, connect the

wiring temporarily, making sure it is all connected
up properly, and the unit and the system work
properly.

• Use only the parts included with the unit to ensure

proper installation. The use of unauthorized parts
can cause malfunctions.

• Consult with your nearest dealer if installation

requires the drilling of holes or other modifications
of the vehicle.

• Install the unit where it does not get in the driver’s

way and cannot injure the passenger if there is a
sudden stop, like an emergency stop.

• The semiconductor laser will be damaged if it

overheats, so don’t install the unit anywhere hot —
for instance, near a heater outlet.

• If installation angle exceeds 60° from horizontal,

the unit might not give its optimum performance.
(Fig. 4)

Fig. 4

60

°

DIN Front/Rear-mount

This unit can be properly installed either from “Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing threaded screw holes at the sides of unit
chassis). For details, refer to the following illustrated installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 5)

Fig. 5

182

53

Removing the Unit (Fig. 6) (Fig. 7)

Fig. 6

Fig. 7

Insert the release pin into the hole in
the bottom of the frame and pull out
to remove the frame.
(When reattaching the frame, point
the side with a groove downwards
and attach it.)

Frame

Insert the supplied extraction keys
into the unit, as shown in the figure,
until they click into place.Keeping
the keys pressed against the sides of
the unit, pull the unit out.

Holder
After inserting the holder into the dash-
board, then select the appropriate tabs
according to the thickness of the dash-
board material and bend them.
(Install as firmly possible using the top
and bottom tabs. To secure, bend the
tabs 90 degrees.)

Dashboard

Rubber bush

Screw

Содержание Suepr Tuner III DEH-P7200







Отзывы: