Pioneer SGY-PM910H L Скачать руководство пользователя страница 5

Страница: 5 / 36

Getting R

eady

Getting R

eady

Product Configuration

Accessories

This product contains the following parts.

Pedaling monitor sensor (right side)

Right transmitter
Junction cable
Strain gauge unit
Junction box

Pedaling monitor sensor part (right side)

For FC-9000

For FC-6800

Chain ring adapter

Strain gauge unit cover x 1 for each type

Pedaling monitor sensor (left side)

Left transmitter
Strain gauge unit
LED

Pedaling monitor sensor part (left side)

Magnet

Patch type x 2

Arm type (right side)

Arm type (left side)

Others

User’s Manual (this document)

•

Warranty Card

•

Important Information for the User

•

Batteries (CR2032) x 2

•

(pre-installed in the left and right sensors)
Right transmitter cover (metallic gray)

•

Hex screws (M2.6 x 8mm) x 3

•

(for the right transmitter x 3)

Hex screws (M2.6 x 5mm) x 3

•

(spare for the right transmitter cover x 3)
Cable ties x 10

•

(for the left magnet x 2, for the right magnet
x 2, spare x 6)
Cushions for the arm type magnet installation x 2

•

Содержание SGY-PM910H L





































Результаты поиска

Содержание SGY-PM910H L

Отзывы:

Бренды по названию

Популярные бренды

Pioneer SGY-PM910H L, Руководство по установке

Результаты поиска

Содержание SGY-PM910H L

Отзывы:

Бренды по названию

Популярные бренды