Pioneer SD-643HD5, Руководство по обслуживанию

Страница: 129 / 206

129
SD-533HD5, SD-643HD5
F RH
STATIC
001
Screen indication
The cross-hatch signal is generated inside the unit, and is auto-
matically displayed in OFFSET CONVER. mode and MANUAL
CONVERGENCE mode. You can turn on and off the cross-hatch
signal with the YELLOW key.
Table 2 OFFSET CONVER DATA
OFFSET CONVER MODE 2
Numeric
Key
Adjustment
Item
Screen Mode
1 V1D 029 082 060 03E 026
2 V1C 020 020 020 020 01E
3 V10 000 000 000 000 000
4 VFP 003 01D 003 01A 036
5 HFP 122 122 122 122 122
6 H1R 001 001 001 001 001
7 HCP 00F 00F 00F 00F 00F
8 H10 015 015 015 015 015
FULL ZOOM CINEMA NATURAL HD FULL
OFFSET CONVER MODE 1
Numeric
Key
Adjustment
Item
Screen Mode
1 DFH 1D0 1D0 1D0 1D0 1D0
2 DFV 0A0 0A0 0A0 0A0 0A0
3 DF1 00F 00F 00F 00F 00F
4 DF2 000 000 000 000 000
5 HPP 14C 14C 14C 14C 14A
6 HPW 00B 00B 00B 00B 00C
7 HTP 02C 02C 02C 02C 02F
8 VTP 033 029 033 02A 00F
FULL ZOOM CINEMA NATURAL HD FULL
The above offset convergence values are common to the
SD-533HD5 and SD-643HD5.
Numeric Key GH GV
0 STATIC STATIC
1 SKEW SKEW
4 KEY KEY
6 PIN PIN
7 LIN LIN
8 SIZE SIZE
If the offset convergence values are as indicated in Table 2,
proceed to 3.3. If the values are not the same, adjust the values
with the numeric keys and VOL +/– keys.
Example:
To check DFI in ZOOM mode of OFFSET CONVER. MODE 1
1
Enter the FACTORY mode.
2
Enter the OFFSET CONVER. MODE 1 by pressing the
INPUT 4 key once.
3
Enter the ZOOM screen mode by pressing the SCREEN mode
key once. (When the unit enters FACTORY mode, the screen
mode automatically becomes FULL.)
4
Check the indication on the screen by pressing the numeric
key 3.
Indication at the bottom of the screen : Z DFI 00F
If the adjustment value is 00F, adjustment is not required.
If the adjustment value is other than 00F, adjust with the VOL
+ or VOL- key so that the value becomes 00F.
3.3 Coarse Adjustment of the Green
(Proceed with 3.3 and afterwards when the DIGITAL CONV.
Assy is not replaced.)
Select adjustment items (STATIC and SIZE of vertical and
horizontal lines, etc.) for each GH and GV, and adjust to roughly
eliminate distortion. (For GV, peripheral pin distortion adjust-
ment is necessary.)
Press the INPUT 4 key three times to enter OFFSET CONVER.
MODE 3.
Press the SCREEN mode key and proceed with the adjustment for
each screen mode.
A B C D
Adjustment data:
MAX
1FF
100
001
CNT 000
3FF
2FF
MIN 200
Data can be adjusted with the VOL+ and VOL- keys.
Screen mode:
F
: FULL
Z : ZOOM
C : CINEMA
N : NATURAL
H : FULL for HD
The Screen modes change cyclically with each press of the
SCREEN mode key.
Adjustment items can be selected with the numeric keys.
See Table below.
A
C
Cyclically changes with the CH+ or CH- key as follows:
B
D
RH RV BH
GV GH BV
• Waveforms adjustable in the coarse adjustment
of the green