Pioneer PDP-LX508A, Руководство по обслуживанию

Страница: 9 / 153

PDP-508XG
9
5 6 7 8
5 6
7
8
C
D
F
A
B
E
Structure of Layers in Service Factory Mode
I N FORMATIO N mode
1. V ERSIO N (1) The soft w are v ersions for each microcomp u ter
2. V ERSIO N (2) The Flash memory v ersions for each de v ice
3. MAI N N G The sh u tdo w n message ID/e v ent times
(Going Clear mode b y [E N TER/SET] key)
3-1. CLEAR Select Yes b y [
l
] key,
l
pressing and hold [E N TER/SET] key
4. TEMPERATURE The temperat u re/FA N rotating stat u s/Room light sensor
5. HOUR METER The HOUR METER/P-COU N T information
6. HDMI SIG N AL I N FO 1 The information of HDMI information files
7. HDMI SIG N AL I N FO 2 The information of HDMI information files
8 . V DEC SIG N AL I N FO 1 The signal information of V DEC
9. V DEC SIG N AL I N FO 2 The signal information of V DEC
PA N EL FACTORY mode Refer to [PA N EL FACTORY MODE]
OPTIO N mode
1. EDID W RITE MODE For factory u se
2. CH PRESET For prod u ction line u se
3. AFT For factory u se
4. SY N C DET For technical analysis
I N ITIALIZE mode
1. SIDE MASK LE V EL For factory u se
1-1. SIDE MASK LE V EL
2. FI N AL SETUP Set to Factory defa u lt settings (it sho u ld perform after
2-1. DATA RESET replacing a MAI N Assy)
3. W ide XGA AUTO For technical analysis
Quick Reference upon Service Visit
2
Mode transition and structure of layers in Service Factory mode
Structure of Layers in Panel Factory Mode 1
1. PA
N EL I N FORMATIO N V ersion indication of the panel
2. PA N EL W ORKS Indications of the acc u m u lated po w er-on time, p u lse-meter
co u nt, and po w er-on co u nt of the panel
3. PO W ER DO WN Indication of the Po w er-do w n history
4. SHUT DO WN Indication of the Sh u tdo w n history
5. PA N EL-1 ADJ (+)
1. V OL SUS
2. V OL OFFSET
• • • • •
8 . V OL Y N OFS4
9. RESET1ST_KSB
10. RESET2 N D_KSB
• • • • •
23. YSTL_FMR_HZ
24. SUS FREQ
6. PA
N EL-2 ADJ (+)
1. R-HIGH
2. G-HIGH
3 .B-HIGH Parameters for the W B adj u stment of the panel, w hich are
4. R-LO W req u ired d u ring adj u stment after panel replacement
5. G-LO W
6. B-LO W
7. ABL Setting of the po w er cons u mption. A setting ta b le is
a v aila b le for each v ertical signal.
To "Str u ct u re of Layers in Panel Factory Mode 2"
Structure of Layers in Panel Factory Mode 2
7. PA N EL FU N CTIO N (+)
1. R-LE V EL
2. G-LE V EL
3. B-LE V EL
4. ADDRESS L1 Items for u se b y engineers
5. ADDRESS L2
• • • • •
11. ADDRESS U4
12. STK MODE
8 . ETC (+)
1. BACKUP DATA For transferring b ack u p data (after replacement of
the DIGITAL Assy)
2. DIGITAL EEPROM To clear data of the digital v ideo
3. PD I N FO.
4. SD I N FO. For clearance of data for the corresponding items.
5. HR-MTR I N FO. The clearing method is the same: Select "CLEAR",
6. PM/B1-B5 u sing [
l
], then hold [E N TER/SET] pressed for at
7. P COU N T I N FO. least 5 seconds. After clearance is completed, {ETC}
8 . MAX TEMP. is a u tomatically selected.
9. RASTER MASK SETUP (+)
1. MASK OFF
2. RST MASK 01 For u se w hile Raster Mask (f u ll mask) is displayed.
• • • • • Use [
i
] or [
j
] to select the type of mask.
26. RST MASK 25
10. PATTE N MASK SETUP (+)
1. MASK OFF
2. PT N MASK 01 For u se w hile Pattern Mask is displayed. Use [
i
] or
• • • • • [
j
] to select the type of mask.
50. PT N MASK 49
11. COMBI MASK SETUP (+)
1. MASK OFF
2. CMB MASK 01 For u se w hile Com b ination Mask is displayed.
• • • • • Use [
i
] or [
j
] to select the type of mask.
1 8 . CMB MASK 17
I N FORMATIO N mode
1. V ERSIO N (1)
2. V ERSIO N (2)
3. MAI N N G
4. TEMPERATURE
5. HOUR METER
6. HDMI SIG
N AL I N FO1
7. HDMI SIG N AL I N FO2
8 . V DEC SIG N AL I N FO1
9. V DEC SIG N AL I N FO2
PA N EL FACTORY mode
1. PA N EL I N FORMATIO N
2. PA N EL W ORKS
3. PO W ER DO WN
4. SHUT DO WN
5. PA N EL-1 ADJ
6. PA N EL-2 ADJ
7. PA N EL FU N CTIO N
8 . ETC.
9. RASTER MASK SETUP
10. PATTE
N MASK SETUP
11. COMBI MASK SETUP
I N ITIALIZE mode
1. SIDE MASK LE V EL
2. FI N AL SETUP
3. W ide XGA AUTO
OPTIO N mode
1. EDID W RITE MODE
2. CH PRESET
3. AFT
4. SY
N C DET
Up
Do w n
• To shift to another mode, press [MUTI N G].
• To shift to another item in a specific mode,
press
[
i
] or [
j
].
• To shift to the next nested layer b elo w for an
item w ith a "(+)" indication, press [E N TER/SET].
To ret u rn to the next nested layer a b o v e,
also press [E N TER/SET].
Mode transition in Service Factory mode
For AM noise pre v ention (Depending on the mode,
b rightness of the screen changes.)
For confirmation of the res u lt of the setting change,
the u nit m u st b e t u rned off then b ack on again.
Modification not req u ired b eca u se these items
are b asically for factory presetting
Settings req u ired after replacement of the panel