Initial Settings
1
Press SRC/OFF and hold until the unit
turns off.
2
Press M.C. to display the initial setting
menu.
3
Turn M.C. to select the initial setting.
After selecting, perform the following proce-
dures to set the initial setting.
FM step
(FM tuning step)
The FM tuning step employed by seek tuning can be
switched between 100 kHz, the preset step, and 50
kHz.
!
If seek tuning is performed in 50 kHz steps, sta-
tions may be tuned in imprecisely. Tune in the sta-
tions with manual tuning or use seek tuning
again.
!
The tuning step remains at 50 kHz during manual
tuning.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the FM tuning step.
100kHz
(100 kHz)
—
50kHz
(50 kHz)
3
Press
M.C.
to confirm the selection.
AM step
(AM tuning step)
The AM tuning step can be switched between 9 kHz,
the preset step, and 10 kHz. When using the tuner in
North, Central or South America, reset the tuning
step from 9 kHz (531 kHz to 1 602 kHz allowable) to 10
kHz (530 kHz to 1 640 kHz allowable).
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select the AM tuning step.
9kHZ
(9 kHz)
—
10kHZ
(10 kHz)
3
Press
M.C.
to confirm the selection.
A-EQ Measurement
(auto-equalizing)
The auto-equalizer is an equalizer curve created by
auto EQ (refer to
page).
You can turn the auto-equalizer on or off.
Rear Speaker
(rear output and subwoofer setting)
This unit
’
s rear output (rear speaker leads output and
RCA rear output) can be used for full-range speaker
(
Full
) or subwoofer (
Subwoofer
) connection. If you
switch the rear output setting to
Subwoofer
, you can
connect a rear speaker lead directly to a subwoofer
without using an auxiliary amp.
Initially, the unit is set for rear full-range speaker con-
nection (
Full
).
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to change the setting.
Subwoofer
(subwoofer)
—
Full
(full-range speak-
er)
!
Even if you change this setting, there is no
output unless you turn the subwoofer output
on (refer to
!
If you change this setting, subwoofer output
in the audio menu will return to the factory
settings.
3
Press
M.C.
to confirm the selection.
Demonstration
(demo display setting)
1
Press
M.C.
to turn the demo display on or off.
Video Signal
(video signal setting)
Be sure to adjust the video signal setting to one that
is suitable for your country.
1
Press
M.C.
to display the setting mode.
2
Turn
M.C.
to select an appropriate video signal.
NTSC
—
PAL
3
Press
M.C.
to confirm the selection.
BT Memory Clear
(resetting the Bluetooth wireless
technology module)
This function is available only for MVH-8250BT.
Bluetooth telephone data can be deleted. To protect
personal information, we recommend deleting this
data before transferring the unit to other persons. The
following settings will be deleted.
!
phone book entries on the Bluetooth telephone
!
preset numbers on the Bluetooth telephone
!
registration assignment of the Bluetooth tele-
phone
!
call history of the Bluetooth telephone
!
information of the connected Bluetooth telephone
!
PIN code
1
Press
M.C.
to display the setting mode.
2
Use
M.C.
to select
Yes
.
Turn to change the mode. Press to select.
Cleared
is displayed and the settings are deleted.
To cancel, select
No
.
!
While this function is in use, do not turn off
the engine.
En
29
English
Section
03
Operating this unit
