+
≠
+
≠
+
≠
+
≠
24. Right
Gray
23. Left
.
14. Connecting cords with RCA pin plugs
(sold separately)
17. System remote control
32. Perform these connections when using
the optional amplfier.
15. Power amp
(sold separately)
1. This Product
4. IP-BUS input (Blue)
3. Antenna jack
5. Multi-CD player
(sold separately)
6. IP-BUS cable
13. Fuse
30. Subwoofer
30. Subwoofer
Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
7.
Blue
When the source is selected the tuner, a control signal is
output.
To Auto-antenna relay control terminal.
If the car features a glass antenna, connect to the antenna
booster power supply terminal (max. 300 mA 12 V DC).
8.
Yellow
To terminal always supplied
with power regardless of
ignition switch position.
9.
Black (ground)
To vehicle (metal) body.
12.
Blue/white
When the source is switched ON,
a control signal is output.
To system control terminal of the
power amp (max. 300 mA 12 V
DC).
16.
Front speaker
18.
White
19.
White/black
20.
Green
26.
Green/black
27.
Front speaker
18.
Rear speaker
25.
Rear speaker
25.
21.
Gray/black
22.
Violet
28.
Violet/black
29.
With a 2 speaker system, do not connect
anything to the speaker leads that are not
connected to speakers.
31.
Orange/white
To lighting switch terminal.
11.
Red
10.
To electric terminal controlled by
ignition switch (12 V DC) ON/OFF.
2. Subwoofer output or
Non-fading output
Note:
•
This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
•
To avoid shorts in the electrical system, be sure
to disconnect the
≠
battery cable before begin-
ning installation.
•
Refer to the owner’s manual for details on con-
necting the power amp and other units, then
make connections correctly.
•
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
•
Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
•
Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
•
Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
•
Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
•
When replacing fuse, be sure to use only fuse of
the rating prescribed on the fuse holder.
•
Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded
or the left and right
≠
speaker leads are com-
mon.
•
Speakers connected to this unit must be high-
power types with minimum rating of 50 W and
impedance of 4 to 8 ohms. Connecting speakers
with output and/or impedance values other than
those noted here may result in the speakers
catching fire, emitting smoke, or becoming dam-
aged.
•
When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue lead to the power terminal
of the auto-antenna. Such connection could cause
excessive current drain and malfunction.
•
To avoid short-circuiting, cover the disconnected
lead with insulating tape. Especially, insulate the
unused speaker leads without fail. There is a pos-
sibility of short-circuiting if the leads are not
insulated.
•
To prevent incorrect connection, the input side of
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col-
ors correctly.
•
If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.
•
The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
•
Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
Installation manuals of both products and con-
nect cords that have the same function.
Connecting the Units
ACC position
ACC
ON
S
T
A
R
T
O
FF
ON
S
T
A
R
T
O
FF
No ACC position
<ENGLISH>
Connection Diagram (Fig. 11)
1. This Product
2. Subwoofer output or Non fading output
3. Antenna jack
4. IP-BUS input (Blue)
5. Multi-CD player (sold separately)
6. IP-BUS cable
7. Yellow/black
If you use a cellular telephone, connect it via the
Audio Mute lead on the cellular telephone. If not,
keep the Audio Mute lead free of any connections.
8. Blue
When the source is selected the tuner, a control
signal is output. To Auto-antenna relay control
terminal. If the car features a grass antenna,
connect to the antenna booster power supply
terminal (max. 300 mA 12 V DC).
9. Yellow
To terminal always supplied with power regard-
less of ignition switch position.
10. Red
To electric terminal controlled by ignition switch
(12 V DC) ON/OFF.
11. Orange/white
To lightning switch terminal.
12. Black (ground)
To vehicle (metal) body.
13. Fuse
14. Connecting cords with RCA pin plugs (sold sepa-
rately)
15. Power amp (sold separately)
16. Blue/white
When the source is switched on, a control signal
output. To system control terminal of the power
amp (max. 300 mA 12 V DC).
17. System remote control
18. Front speaker
19. White
20. White/black
21. Gray
22. Gray/black
23. Left
24. Right
25. Rear speaker
26. Green
27. Green/black
28. Violet
29. Violet/black
30. Subwoofer
31. With a 2 speaker system, do not connect anything
to the speaker leads that are not connected to
speakers.
32. Perform these connections when using the
optional amplifier.
Fig. 11
