Pioneer ELITE VSX-LX304 Скачать руководство пользователя страница 138

Страница: 138 / 180

138

≫

≫

≫

≫

≫

≫

Setting Item

Default Value

Setting Details

USB Power Out

at Standby

Off

When this function is set to "On", power can be

supplied to devices connected to the USB port on

the rear panel even when the unit is in the standby

mode. Supply of power to USB devices in the

standby mode is not supported for the USB port on

the front panel.

•

When this function is set to "On", the power

consumption in standby state increases,

however, the increase in power consumption is

minimized by automatically entering the HYBRID

STANDBY mode where only the essential circuits

operate.

Network Standby

When this function is set to "On", the network

function works even in standby state, and you can

turn on the power of the unit via network using an

application such as Pioneer Remote App that can

control this unit.

•

When this function is set to "On", the power

consumption in standby state increases,

however, the increase in power consumption is

minimized by automatically entering the HYBRID

STANDBY mode where only the essential circuits

operate. Note that even if this function is set to

"Off", when any of the HDMI CEC (

p136

HDMI Standby Through (

p136

), USB Power

Out at Standby (

p138

) and Bluetooth

Wakeup (

p138

) functions is enabled, this

function will be in "On" state regardless of the

setting.

•

When connection to the network is lost, "Network

Standby" may be disabled to reduce power

consumption. In such a case, turn the unit on by

using the power button on the remote controller

or main unit.

Setting Item

Default Value

Setting Details

Bluetooth Wakeup Off

This function wakes up the unit on standby by

connecting a BLUETOOTH-enabled device.

"On": When this function is used

"Off": When this function is not used

•

When this function is set to "On", the power

consumption in standby state increases,

however, the increase in power consumption

is minimized by automatically entering the

HYBRID STANDBY mode where only the

essential circuits operate.

•

This setting is fixed to "Off" if "Network/

Bluetooth" - "Bluetooth" - "Auto Input Change" is

set to "Off".

•

Wait for a while if "Network Standby" and "Bluetooth Wakeup" cannot be selected. It can

be selected when the network function is activated.

Содержание ELITE VSX-LX304





















































































































































































Результаты поиска

Содержание ELITE VSX-LX304

Отзывы:

Похожие инструкции для ELITE VSX-LX304

Бренды по названию

Популярные бренды

Pioneer ELITE VSX-LX304, Инструкция по эксплуатации

Результаты поиска

Содержание ELITE VSX-LX304

Отзывы:

Похожие инструкции для ELITE VSX-LX304

Бренды по названию

Популярные бренды