Pioneer Elite VSX-LX104 Скачать руководство пользователя страница 142

Страница: 142 / 152

142

≫

≫

≫

≫

≫

≫

Network function

•

If you cannot select a network service, start up the network function to select it. It may take approx. one minute to start it up.

•

When the NET indicator is blinking, this unit is not properly connected to the home network.

•

Unplug and plug the power cords of this unit and the router, or restart the router.

•

If the desired router is not displayed in the access point list, it may be set to hide SSID, or the ANY connection may be off. Change the setting and

try again.

Check the following if the problem persists after you have confirmed the above.

❏

Cannot access the Internet radio

•

In the case the service provider has terminated the service, the network service or contents may not be used on this unit.

•

Check if your modem and router are properly connected, and they are both turned on.

• Check if the LAN side port on the router is properly connected to this unit.

•

Check if connecting to Internet from other devices is possible. If it is not possible, turn off all devices connected to the network, wait for a while,

and then turn on the devices again.

•

Depending on ISP, setting the proxy server is required.

• Check if the router and modem you are using are supported by your ISP.

❏

Cannot access the network server

•

This unit needs to be connected to the same router as the network server.

•

This unit supports the Windows Media

Player 11 or 12 network servers, or NASes that support the home network function.

•

Windows Media

Player may require some settings. Refer to "Playing back files on a PC and NAS (Music Server)".

•

When using a PC, only the music files registered in the library of Windows Media

Player can be played.

(

p59

)

❏

Sound is interrupted when playing music files on the network server

•

Check if the network server meets the requirements for operation.

•

When the PC is serving as the network server, quit application software other than the server software (Windows Media

Player 12, etc.).

•

If the PC is downloading or copying large files, the playback sound may be interrupted.

Содержание Elite VSX-LX104

























































































































































Результаты поиска

Содержание Elite VSX-LX104

Отзывы:

Похожие инструкции для Elite VSX-LX104

Бренды по названию

Популярные бренды

Pioneer Elite VSX-LX104, Инструкция по эксплуатации

Результаты поиска

Содержание Elite VSX-LX104

Отзывы:

Похожие инструкции для Elite VSX-LX104

Бренды по названию

Популярные бренды