Pioneer Elite VSX-43TX, Руководство по эксплуатации

Страница: 86 / 104

86
Fine Tuning Your System
Follow steps 1-5 on page 79, if necessary, to get
to the starting point mentioned here.
1 BASSPEAK LEVEL should be
selected, if it isn’t use the
5∞
buttons to select it. Press
ENTER.
LOUDNESS MIDNIGHT TONE DNR ATT STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO
Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L C R LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L S S R S
AUTO
RF
DIGITAL
dB SIGNAL
SP A B
ANALOG
2
Use the
5∞
buttons to select
SETTING START or SETTING
CANCEL. Press ENTER.
SETTING START: The MASTER VOLUME is set
to MIN (----dB), a test tone plays back and you
make the setting (go to step 3).
LOUDNESS MIDNIGHT TONE DNR ATT STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L C R LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L
S
S R
S
AUTO
RF
DIGITAL
dB SIGNAL
SP A B
ANALOG
SETTING CANCEL: This setting won't limit the
peak level of the LFE channel.
LOUDNESS MIDNIGHT TONE DNR ATT STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L C R LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L S S R S
AUTO
RF
DIGITAL
dB SIGNAL
SP A B
ANALOG
If you selected SETTING CANCEL go to step 4.
BASS PEAK LEVEL
The LFE (Low Frequency Effect) channel in Dolby Digital and DTS program sources can produce heavily
concentrated ultra-low bass tones that may exceed the capabilities of your speaker system. The following steps
show you how to set the peak level for the LFE channel. If continuing from the preceding page the BASS PEAK
LEVEL should be selected.
CHANNEL
−
CHANNEL
+
DTV ON/OFF BAND
D.ACCESS MPX CLASS
MENU TOP MENU TUNER EDIT
GUIDE SYSTEM
SETUP
AUDIO RETURN
ST
TUNE
MASTER
VOLUME
ST
TUNE
ENTER
1-5
3
Use the
5∞
buttons to adjust the
test tones and specify the bass
peak level.
LOUDNESS MIDNIGHT TONE DNR ATT STEREO
TUNED
RDS
Hi-BIT/
MULTI-ROOM
SAMPLING
EON
RF ATT
MONO Neo :6
DIGITAL
DTS ES EX
MPEG AAC
STEREO
PRO LOGIC
DSP
L C
R LFE
AUTO
SB CH
ON MOVIE
MUSIC
OFF
L S S R S
AUTO
RF
DIGITAL
dB SIGNAL
SP A B
ANALOG
If you set this level before the receiver
will have that level input but it will not appear on
this setup screen. (The screen will always open
with the level showing [- - -].)
1
Raise the level gradually.
2
Set the bass peak level at the point just before
the tone starts to distort.
Be careful! Test tones play back at loud
volumes . Make sure there are no infants or
small children in the room at distortion level.
You can leave this setup any time by pressing
ENTER.
If the YES or PLUS setting on the subwoofer is
selected the test tone will only play back from the
subwoofer. If not, the test tone will play back
from all speakers set to LARGE except for the
subwoofer.
4
Press ENTER.
The display on the receiver will show RESUME
and the MASTER VOLUME will return to its
original position.
5 EXIT should be selected (if it isn’t
use the
5∞
buttons to select it)
and press ENTER.
Next, if you want, proceed to DYNAMIC RANGE
CONTROL
STANDBY/ON
MOVIE MUSIC
MULTI JOG
ENTER
STANDBY
PHONES
SPEAKERS
SIGNAL
SELECT HI-BIT
HI-SAMPLING
SB CH
MODE
SET UP RETURN
TONE
TONE CONTROL
BASS/TREBLE
BAND MIDNIGHT LOUDNESS
MULTI JOG CONTROL
1-5