Pioneer Elite SC-97, Руководство по эксплуатации

Страница: 93 / 171

93
Using other functions
09
Setting What it does Option(s)
ASP
(Aspect)
<h>
Specifies the aspect ratio when input signals are output at the HDMI
output. Make your desired settings while checking each setting on
your display (if the image doesn’t match your monitor type, cropping
or black bands appear). THROUGH
NORMAL
a ! The default value changes depending on the type of input ( page 97 ).
! If the video picture deteriorates when this settings is switched ON , switch it OFF .
! When connected with a video device using the component video input terminals, set this setting to ON and view the HDMI
OUT 1 or HDMI OUT 2 terminal’s video.
! When upscaling to 4K or 1080p, video may not be output correctly depending on the HDMI cable. In this case, set this setting
to OFF .
b ! When set to a resolution with which the TV (monitor) is not compatible, no picture is output. Also, in some cases no picture
will be output due to copyright protection signals. In this case, change the setting.
!
When AUTO is selected, the resolution is selected automatically according to the capacity of the TV (monitor) connected by
HDMI. When PURE is selected, the signals are output with the same resolution as when input (see About the video converter on
page 37 ).
!
When 1080/24p or 4K/24p is selected, the movement may be unnatural or the picture unclear, depending on the video signal
being input. In this case, set the resolution to something other than 1080/24p or 4K/24p .
!
When PURE is selected and the input signal is 480i, the on-screen display cannot be displayed.
c This can only be set when AUTO , 4K , or 4K/24p is selected in SCAL . This is effective when upscaling to 4K from an input signal
other than 4K.
d
!
P.MOTION is disabled when PCINEMA is set to ON .
! This setting have the effect only for pictures recorded in the interlaced scan format (480i/576i or 1080i signals).
e ! This setting is only displayed when the video signals below are being input:
—
480i, 576i, 480p, 576p, 720p, 1080i analog video signals
—
480i, 576i, 480p, 576p, 720p, 1080i, 1080p, 1080p24 HDMI video signals
f Adjustment is not possible unless
V.ADJ
(Advanced Video Adjust) is set to
MEMORY
.
g This adjustment is only possible when 480i signals are being input from the composite video jacks.
h
! If the image doesn’t match your monitor type, adjust the aspect ratio on the source component or on the monitor.
! This setting is only displayed when 480i/p or 576i/p video signals are being input.
Switching the output (OUTPUT PARAMETER)
You can press
OUT P.
to switch the output of speaker terminals or HDMI terminals to be played.
Switching the speaker terminals
If you selected 9.2.2ch TMd/FH , 7.2.2/7.2ch + SP-B or 5.2ch + SP-B Bi-Amp at Speaker system setting on page
113 , you can switch between speakers using the
OUT P.
button.
If you selected 7.2.2/5.2.2/7.2ch , 7.2.4ch SB Pre out , 7.2.4ch Front Pre out , 7.2.2ch Front Bi-Amp ,
7.2ch + HDZONE
,
5.2 Bi-Amp+HDZONE
,
5.2ch F+Surr Bi-Amp
,
5.2ch F+C Bi-Amp
,
5.2ch C+Surr Bi-Amp
,
Multi-ZONE Music , 5.2 +ZONE 2+HDZONE or 5.2 +ZONE 2+ZONE 3 , the button will simply switch your main
speaker terminals on or off.
1 Press OUT P..
!
You can perform the same operation by pressing SPEAKERS on the front panel.
2 Use
i
/
j
to select ‘SP’.
3 Use
k
/
l
to switch the speaker terminals to be played.
As mentioned above, if you have selected
7.2.2/5.2.2/7.2ch
,
7.2.4ch SB Pre out
,
7.2.4ch Front Pre out
,
7.2.2ch Front Bi-Amp , 7.2ch + HDZONE , 5.2 Bi-Amp+HDZONE , 5.2ch F+Surr Bi-Amp , 5.2ch F+C Bi-Amp ,
5.2ch C+Surr Bi-Amp , Multi-ZONE Music , 5.2 +ZONE 2+HDZONE or 5.2 +ZONE 2+ZONE 3 , the button will
simply switch your main speaker terminal (A) on or off (Pre-AMP mode).
The pre-amp mode is a mode for reducing power consumption when power amplifiers are connected to the
receiver’s PRE OUT terminals by individually turning off the power of the amplifiers for those channels.
Press repeatedly to choose a speaker terminal option:
When you select 9.2.2ch TMd/FH , you can select from:
!
SP: TMd/FH ON
– Top middle or front height channels are added to the front, center, surround and surround
back channels (maximum 7 channels) and a maximum of 9 channels are output. The top middle and front
height channels are switched automatically according to the audio input signal.
!
SP: TMd ON – Top middle channels are added to the front, center, surround and surround back channels
(maximum 7 channels) and a maximum of 9 channels are output.
!
SP: FH ON – Front height channels are added to the front, center, surround and surround back channels
(maximum 7 channels) and a maximum of 9 channels are output.
!
SP: OFF – No sound is output from the speakers.
When you select 7.2.2/7.2ch + SP-B , you can select from:
!
SP: A ON – Sound is output from the A-speaker terminals (up to 9 channels (front, center, surround, surround
back and top middle), depending on the source).
!
SP: B ON – Sound is output from the two speakers connected to the B-speaker terminals ( EXTRA 1 ).
Multichannel sources will not be heard.
!
SP: A+B ON
– Sound is output from the A-speaker terminals (up to 7 channels (front, center, surround and
surround back), depending on the source), the two speakers connected to the B-speaker terminals ( EXTRA
1
), and the subwoofer. The sound from the B-speaker terminals will be the same as the sound from the
A-speaker terminals (multichannel sources will be downmixed to 2 channels).
!
SP: OFF
– No sound is output from the speakers.
When you select 5.2ch + SP-B Bi-Amp , you can select from:
! SP: A ON – Sound is output from the A-speaker terminals (up to 5 channels (front, center and surround),
depending on the source).
! SP: B ON – Sound is output from the two speakers connected to the B-speaker terminals ( EXTRA 1 and
SURROUND BACK ). Multichannel sources will not be heard.
! SP: A+B ON – Sound is output from the A-speaker terminals (up to 5 channels (front, center and surround),
depending on the source), the two speakers connected to the B-speaker terminals (
EXTRA 1
and
SURROUND
BACK ), and the subwoofer. The sound from the B-speaker terminals will be the same as the sound from the
A-speaker terminals (multichannel sources will be downmixed to 2 channels).
!
SP: OFF – No sound is output from the speakers.
Notes
! When 7.2.2/7.2ch + SP-B or 5.2ch + SP-B Bi-Amp is selected for the Speaker System setting ( page 113 ) and
Speaker B Link ( HDMI Setup on page 85 ) is set to “ON”, the setting of the speaker terminals that are played
changes automatically when HDMI OUT 1 and HDMI OUT 2 are switched. For details, see Switching the
HDMI output on page 94 .
! The subwoofer output depends on the settings you made in Manual speaker setup on page 113 . However, if
SP: B ON
is selected above, no sound is heard from the subwoofer (the LFE channel is not downmixed).
! All speaker systems (except 7.2.2/7.2ch + SP-B connections) are switched off when headphones are
connected.